1. Introduction
This manual provides essential instructions for the installation, operation, and maintenance of your Urmet 1132/1 Electronic White Interphone. Please read this manual thoroughly before installation and use to ensure proper function and safety. Keep this manual for future reference.
2. Safety Information
- Electrical Safety: Installation should only be performed by qualified personnel in accordance with local electrical codes and regulations. Disconnect power before performing any wiring or maintenance.
- Handling: Handle the interphone with care to prevent damage. Avoid dropping or subjecting it to strong impacts.
- Environment: Do not expose the unit to extreme temperatures, humidity, or direct sunlight. Ensure the installation location is dry and protected.
- Cleaning: Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.
3. Package Contents
Verify that all items are present in the package:
- Urmet 1132/1 Electronic White Interphone Unit (Handset and Base)
- Mounting Screws and Wall Plugs (may vary by package)
- Instruction Manual (this document)
4. Product Overview
The Urmet 1132/1 is a standard electronic interphone designed for residential or office use. It features a classic handset design for clear audio communication and a button for door release functionality.
Figure 1: Urmet 1132/1 Electronic White Interphone. This image displays the white interphone unit, comprising a wall-mounted base and a handset connected by a coiled cord. A small, rectangular button is visible on the upper right side of the base unit.
Key Components:
- Handset: Used for speaking and listening.
- Base Unit: Mounts to the wall and houses the internal electronics and connection terminals.
- Door Release Button: (Refer to Figure 1, upper right button) Activates the electric door lock to allow entry.
5. Setup and Installation
Important: Installation of this interphone system involves electrical wiring. It is strongly recommended that installation be carried out by a qualified electrician or experienced technician to ensure safety and proper functionality.
General Installation Steps (for qualified personnel):
- Power Disconnection: Before beginning any work, ensure that the main power supply to the interphone system is completely disconnected at the circuit breaker.
- Mounting Location: Choose a suitable indoor location for the interphone, typically near the entrance or in a central area. Ensure it is at an accessible height.
- Mounting the Base Unit:
- Carefully open the interphone base unit to access the mounting holes and wiring terminals.
- Mark the positions for drilling on the wall using the base unit as a template.
- Drill holes and insert wall plugs (if necessary).
- Secure the base unit to the wall using the provided screws, but do not fully tighten yet.
- Wiring Connections:
- Refer to the specific wiring diagram provided with your interphone system (not included in this general manual). The Urmet 1132/1 is designed to be compatible with existing Urmet 4+N systems.
- Connect the incoming wires from the outdoor call panel and power supply to the corresponding terminals on the interphone base unit. Ensure all connections are secure and correctly polarized.
- Double-check all wiring against the system diagram to prevent damage or malfunction.
- Final Assembly:
- Once wiring is complete, carefully close the interphone base unit cover.
- Securely tighten the mounting screws.
- Place the handset onto the base unit cradle.
- Power Restoration and Testing: Restore power to the system. Test the interphone by making a call from the outdoor panel and verifying two-way communication and door release functionality.
6. Operating Instructions
Receiving a Call:
- When someone presses the call button at the outdoor panel, your interphone will ring.
- Lift the handset from its cradle to answer the call.
- Speak into the handset and listen for the visitor's response.
- To end the call, simply replace the handset onto the base unit.
Opening the Door:
- During an active conversation (handset lifted) or immediately after receiving a call, press the door release button (refer to Figure 1, upper right button on the base unit).
- The electric door lock will momentarily activate, allowing the visitor to enter.
- Replace the handset when finished.
7. Maintenance
- Cleaning: Regularly wipe the interphone unit with a soft, dry, or slightly damp cloth. Do not use harsh chemicals, abrasive cleaners, or excessive moisture.
- Inspection: Periodically check the coiled cord for any signs of wear or damage. Ensure the handset sits securely in its cradle.
- No User-Serviceable Parts: The internal components of the interphone are not user-serviceable. Do not attempt to open or repair the unit yourself. Contact qualified service personnel for any repairs.
8. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| No ring when outdoor panel button is pressed. |
|
|
| No sound or distorted sound during conversation. |
|
|
| Door release button does not work. |
|
|
If the problem persists after attempting these solutions, please contact qualified service personnel or your supplier for assistance. Do not attempt to repair the unit yourself.
9. Specifications
| Brand | Urmet |
| Model Name | 1132/1 |
| Material | Plastic |
| Color | White |
| Item Weight | 4.54 grams |
10. Warranty and Support
For warranty information, please refer to the documentation provided at the time of purchase or contact your retailer. Urmet products typically come with a manufacturer's warranty covering defects in materials and workmanship.
For technical support or service inquiries, please contact your local Urmet distributor or the point of purchase. Provide your model number (1132/1) and a detailed description of the issue when seeking support.
