Introduction
Thank you for choosing the Proventa Solar LED Wall Light. This manual provides essential information for the safe installation, operation, and maintenance of your new solar light. Please read these instructions carefully before use and retain them for future reference.
Package Contents
- 1 x Proventa Solar LED Wall Light (Model B08NC14HCH)
- 1 x Accessory Bag (screws, wall plugs)
- 1 x User Manual
Safety Information
- Ensure the mounting surface is stable and can support the weight of the light.
- Do not attempt to disassemble or modify the product, as this will void the warranty and may cause damage.
- Keep the solar panel clean to ensure optimal charging efficiency.
- This product is designed for outdoor use with an IP44 rating, protecting against splashing water. Do not submerge in water.
- The light contains a LiFePO4 battery. Dispose of batteries responsibly according to local regulations.
Image: The Proventa Solar LED Wall Light, showing its warm white illumination and integrated sensors.
Setup and Installation
Follow these steps to properly install your solar LED wall light:
- Choose a Location: Select an outdoor location that receives direct sunlight for at least 6-8 hours daily to ensure optimal battery charging. Avoid areas under eaves, trees, or other obstructions that might block sunlight or trigger the motion sensor unnecessarily.
- Mounting Height: For best motion detection performance, install the light at a height of less than 2.5 meters (approximately 8.2 feet). The PIR sensor has a detection range of 6-8 meters.
- Mark Drill Holes: Hold the light against the desired mounting surface and mark the positions for the drill holes.
- Drill Holes: Drill holes at the marked positions. Insert the provided wall plugs if necessary.
- Secure the Light: Align the light with the drilled holes and secure it firmly using the provided screws.
- Initial Charge: Allow the light to charge in direct sunlight for at least 24-48 hours before first use to ensure the battery is fully charged.
Image: Components of the Proventa Solar LED Wall Light, highlighting the monocrystalline solar panel and integrated PIR motion and light sensors.
Operating Instructions
The Proventa Solar LED Wall Light features an integrated light sensor and PIR motion sensor, offering three adjustable operating modes. The light automatically turns on at dusk (light sensor sensitivity: 25 lux) and off at dawn.
Selecting Operating Modes
A small button or switch is typically located on the unit to cycle through the modes. Press the button repeatedly to select your desired mode:
- Mode A (Motion Activated - Full Brightness): The light remains off until motion is detected. Upon detection, it illuminates at full brightness (400 lumens) for approximately 10 seconds, then turns off.
- Mode B (Dim + Motion Activated - Full Brightness): The light stays on at a dim level (20 lumens) at night. When motion is detected, it switches to full brightness (300 lumens) for approximately 10 seconds, then returns to the dim level.
- Mode C (Constant Dim Light): The light illuminates at a constant dim level (50 lumens) throughout the night, regardless of motion.
Image: Visual representation of the three distinct operating modes (A, B, C) for the Proventa Solar LED Wall Light, detailing light output and duration.
Maintenance
Regular maintenance ensures the longevity and optimal performance of your solar light.
- Clean the Solar Panel: Periodically wipe the solar panel with a soft, damp cloth to remove dust, dirt, leaves, or snow. A clean panel ensures maximum sunlight absorption and charging efficiency.
- Inspect Mounting: Check the mounting screws and bracket periodically to ensure the light remains securely attached to the wall.
- Battery: The integrated LiFePO4 battery is designed for long life (average 30,000 hours for the LED). It is not user-replaceable. If the light's performance significantly degrades over time, it may indicate the end of the battery's lifespan.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on at night. |
|
|
| Motion sensor is not detecting movement or is too sensitive. |
|
|
| Light duration is shorter than expected. |
|
|
Product Specifications
| Brand | Proventa |
| Model | B08NC14HCH |
| Material | Stainless Steel, Polycarbonate |
| Dimensions (L x W x H) | 16.5 x 12.5 x 9.5 cm (6.5 x 4.9 x 3.7 inches) |
| Weight | 640 g (1.41 lbs) |
| Power | 3.3 W |
| Luminous Flux | 400 lm |
| Color Temperature | 2700 K (Warm White) |
| Beam Angle | 120° |
| Average Lifespan | 30,000 hours |
| Dimmable | Yes, 3 modes |
| Protection Class | IP44 (Splash-proof) |
| Battery | LiFePO4 2000 mAh 3.2 V |
| PIR Sensor Detection Range | 6-8 m |
| Recommended Mounting Height | <2.5 m |
| Lighting Range | 6-7 m |
| Light Sensor Sensitivity | 25 lux |
| Electrical Insulation Class | III |
| Color | Black |
Image: Detailed dimensions of the Proventa Solar LED Wall Light (16.5 cm length, 12.5 cm height, 9.5 cm depth).
Warranty Information
Specific warranty details are not provided in the product information. Please refer to your purchase documentation or contact the retailer for information regarding warranty coverage and terms.
Customer Support
For any questions, technical assistance, or issues not covered in this manual, please contact your retailer or the Proventa customer service department. Contact information can typically be found on the product packaging or the retailer's website.