PARTPHONER Dusk to Dawn Outdoor Post Light Instruction Manual

1. Introduction

This manual provides instructions for the installation, operation, and maintenance of your PARTPHONER Dusk to Dawn Outdoor Post Light. This hardwired 120V fixture is designed for outdoor use, featuring a durable aluminum body, clear glass panels, and an integrated photocell sensor for automatic operation.

Image 1.1: The PARTPHONER Dusk to Dawn Outdoor Post Light, showing the main fixture and the separate pier mount base. The fixture includes a visible photocell sensor for automatic light control.

Image 1.2: Close-up view highlighting the die-cast aluminum construction of the light fixture's top and the sturdy clear glass panels.

The fixture is constructed from die-cast aluminum and sturdy clear glass, designed to withstand various weather conditions. It is rated IP65 waterproof, ensuring protection against dust and water ingress.

Image 1.3: The outdoor post light shown in a rainy environment, illustrating its IP65 waterproof rating.

2. Important Safety Information

Please read all instructions carefully before installation and use. Retain this manual for future reference.

• WARNING: Risk of electric shock. Disconnect power at the circuit breaker or fuse box before installation or servicing.
• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC). Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• Ensure the fixture is properly grounded.
• Do not install this fixture on a surface that is not stable or capable of supporting its weight.
• Use only bulbs that comply with the specified wattage and base type (E26, max 100W).
• Do not handle the fixture or attempt maintenance while power is connected.
• Keep flammable materials away from the light fixture when in operation.

3. Package Contents

Verify that all components are present and undamaged before proceeding with installation.

• Outdoor Post Light Fixture (1)
• Pier Mount Base (1)
• Mounting Hardware Kit (screws, wire nuts)
• Instruction Manual (1)

Note: Bulb is not included.

4. Specifications

Image 4.1: Diagram illustrating the dimensions of the post light fixture (18 inches height, 6.5 inches width) and the pier mount base (5.6 x 5.6 inches). It also indicates an E26 bulb base and a maximum wattage of 100W.

5. Installation Instructions

This post light fixture offers two mounting options: Pole Mount or Pier Mount. Ensure power is disconnected at the circuit breaker before beginning installation.

Image 5.1: Diagram showing two installation methods: 'A' for Pole Mount, which fits a 3-inch diameter lamp post, and 'B' for Pier Mount, utilizing the included base for installation on a flat surface.

5.1. General Wiring Steps (Hardwired 120V)

1. Turn off power: Locate the circuit breaker controlling the outdoor lighting circuit and switch it to the OFF position. Verify power is off using a voltage tester.
2. Prepare wires: Strip approximately 3/4 inch of insulation from the ends of the house supply wires and the fixture wires.
3. Connect wires: Use the provided wire nuts to connect the wires as follows:
   • Connect the black fixture wire to the black (hot) supply wire.
   • Connect the white fixture wire to the white (neutral) supply wire.
   • Connect the green or bare copper fixture wire to the green or bare copper (ground) supply wire.
4. Secure connections: Ensure all wire nuts are tightly secured and no bare wire is exposed.

5.2. Pier Mount Installation

1. Prepare mounting surface: Ensure the pier or column surface is flat, stable, and has an opening for electrical wiring.
2. Attach pier mount base: Position the pier mount base over the wiring opening. Mark the locations for drilling mounting holes. Drill pilot holes if necessary.
3. Secure base: Feed the supply wires through the center hole of the pier mount base. Secure the base to the surface using appropriate screws (not always included, may require specific hardware for your surface type).
4. Mount fixture: Place the post light fixture onto the pier mount base, aligning the mounting holes.
5. Complete wiring: Follow the general wiring steps (Section 5.1).
6. Secure fixture: Fasten the fixture to the pier mount base using the provided screws.
7. Install bulb: Screw an E26 base bulb (max 100W) into the socket.

Image 5.2: The outdoor post light fully assembled and installed on its pier mount base, ready for operation.

5.3. Pole Mount Installation

This fixture is designed to fit a standard 3-inch diameter lamp post.

1. Prepare lamp post: Ensure the lamp post is securely installed and has electrical wiring accessible at the top.
2. Mount fixture: Slide the post light fixture directly onto the top of the 3-inch diameter lamp post.
3. Complete wiring: Follow the general wiring steps (Section 5.1).
4. Secure fixture: Tighten the set screws on the base of the fixture to secure it to the lamp post.
5. Install bulb: Screw an E26 base bulb (max 100W) into the socket.

6. Operating Instructions

This outdoor post light is equipped with a built-in photocell sensor, enabling automatic dusk-to-dawn operation.

1. Power On: After installation, restore power to the circuit at the breaker.
2. Automatic Operation: The integrated photocell sensor detects ambient light levels. The light fixture will automatically turn on when it detects low light conditions (dusk) and turn off when it detects sufficient light (dawn).
3. Sensor Placement: Ensure the photocell sensor (small circular component on the fixture base) is not obstructed by objects, shadows, or other light sources, as this may interfere with its proper function.

Image 6.1: The post light operating at night, providing illumination from a pillar mount.

7. Care and Maintenance

Regular maintenance helps ensure the longevity and optimal performance of your outdoor post light.

• Cleaning: Periodically clean the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or glass. Ensure power is off before cleaning.
• Glass Panels: Clean the clear glass panels to maintain light output and sensor functionality.
• Bulb Replacement: Disconnect power before replacing the bulb. Allow the old bulb to cool completely before removal. Use only E26 base bulbs with a maximum wattage of 100W.
• Inspection: Periodically inspect the wiring and connections for any signs of wear, damage, or corrosion. Address any issues promptly.

8. Troubleshooting

If you experience issues with your post light, refer to the following common problems and solutions:

9. Warranty and Support

For warranty information or technical support, please contact PARTPHONER customer service. Refer to your purchase documentation for specific warranty terms and contact details.

You can also visit the official PARTPHONER store for more product information and support resources: PARTPHONER Store