Safety Information
WARNING: This product can expose you to chemicals including Di(2-ethylhexyl)phthalate (DEHP), which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov.
Always read and follow all instructions in this owner's manual and on the equipment. Failure to follow instructions can cause severe injury, death, or property damage.
Before installing, operating, or servicing this equipment, read this entire manual and all labels on the equipment. Always disconnect power to the pump and filter before performing any service.
Product Overview
Key Features
- Chemical resistant, fiberglass reinforced polypropylene tank for exceptional strength and long life.
- Unique internal flow path ensures optimum filtration and backwashing efficiency.
- Four large-capacity cartridges provide maximum filter surface area for greater dirt-trapping capacity and longer periods between cleanings.
- Compatible with valves: 261050 (2" HiFlow w/plumbing), 261055 (2" MPV), 263064 (Push Pull Valve, 7.5" Center).
- Valve sold separately.
Components
The Pentair D.E. Cartridge Style Pool Filter consists of a durable tank, internal filter cartridges, a pressure gauge, and connection ports for your pool's plumbing system. The design allows for efficient filtration and easy maintenance.
Figure 1: External view of the Pentair D.E. Cartridge Style Pool Filter.
Figure 2: Internal view showing the four large-capacity filter cartridges.
Setup and Installation
Proper installation is crucial for the optimal performance and longevity of your Pentair D.E. filter. It is recommended to consult a qualified pool professional for installation if you are unsure about any steps.
General Installation Steps:
- Site Selection: Choose a level, well-drained area for the filter, ensuring adequate clearance for maintenance and access to plumbing.
- Plumbing Connections: Connect the filter to your pool's pump and return lines using appropriate PVC piping and fittings. Ensure all connections are secure and watertight.
- Valve Installation: Install the compatible multi-port or push-pull valve (sold separately) according to its specific instructions.
- Pressure Gauge: Install the pressure gauge on the top of the filter tank.
- Initial Startup: Follow the initial startup procedure outlined in the Operating Instructions section to properly charge the filter with D.E. powder.
Installation Overview (Generic D.E. Filter):
Video 1: This video provides a general overview of D.E. filter installation and cleaning. Note that the product shown is from XtremepowerUS, not Pentair, but the principles of D.E. filter operation and maintenance are similar.
Video 2: This video demonstrates the installation and cleaning process for a D.E. filter. Note that the product shown is from ihubdeal, not Pentair, but the general steps for D.E. filter setup and maintenance are applicable.
Operating Instructions
Once installed, operate your Pentair D.E. filter by turning on your pool pump. The filter will begin circulating water, trapping microscopic particles with the D.E. powder on the cartridges. Monitor the pressure gauge regularly.
Initial Filter Startup:
- Ensure the return line is open.
- Stand clear of the filter. Start the pump.
- Make sure water is returning to the pool. Note the clean filter pressure gauge reading.
- Add the recommended amount of D.E. powder to the skimmer while the pump is running.
Maintenance
Regular maintenance ensures efficient filtration and extends the life of your filter. The D.E. filter requires periodic cleaning of its cartridges.
Cartridge Cleaning:
- Stop the pump. Open the air relief valve to release pressure.
- Remove the clamp and top of the filter tank.
- Remove the manifold and individual filter cartridges.
- The filter cartridges can be cleaned by hosing them down with a direct spray at a proper angle to dislodge D.E. and debris.
- Reassemble the cartridges and manifold, ensuring proper alignment.
- Replace the top and tighten the clamp securely.
- Follow the Initial Filter Startup procedure to recharge with D.E. powder.
NOTE: If operating pressure rises 8-10 PSI above the clean filter pressure, or if the flow rate decreases, it's time to clean the filter cartridges.
NOTE: The filter should be manually cleaned at least once per swimming season, or more frequently depending on usage and water conditions.
Maintenance Overview (Generic D.E. Filter):
Video 1: This video provides a general overview of D.E. filter installation and cleaning. Note that the product shown is from XtremepowerUS, not Pentair, but the principles of D.E. filter operation and maintenance are similar.
Video 2: This video demonstrates the installation and cleaning process for a D.E. filter. Note that the product shown is from ihubdeal, not Pentair, but the general steps for D.E. filter setup and maintenance are applicable.
Troubleshooting
If you encounter issues with your filter, refer to the following common troubleshooting tips:
- Low Flow/High Pressure: This usually indicates dirty filter cartridges. Perform a cartridge cleaning as described in the Maintenance section.
- Cloudy Water: Ensure proper D.E. powder levels. Check for damaged cartridges or a faulty manifold. Verify chemical balance of the pool water.
- Leaking: Inspect all plumbing connections, O-rings, and the filter tank clamp for proper seating and tightness.
For persistent issues, contact Pentair customer support or a certified pool technician.
Specifications
- Manufacturer: Pentair
- Model Number: EC-188592
- ASIN: B08MWXLF94
- Filter Type: D.E. Cartridge Style
- Tank Material: Fiberglass reinforced polypropylene
Warranty and Support
For warranty information, please refer to the documentation provided with your product at the time of purchase or visit the official Pentair website. For technical support, replacement parts, or service, contact Pentair customer service directly.
Protection plans may be available for purchase separately. Please check with your retailer for details.
