1. Introduction
This manual provides detailed instructions for the installation, configuration, and operation of your D-Link DGS-1100-05V2 Managed Smart Switch. This 5-port Gigabit switch offers advanced Layer 2 functionality, including VLAN support, Quality of Service (QoS), and 802.3az Energy Efficient Ethernet (EEE), making it suitable for small to medium-sized enterprise networks.
2. Package Contents
Verify that your package contains the following items:
- DGS-1100-05V2 5-Port Gigabit Managed Smart Switch
- Power Adapter
- Mounting Kit (if applicable)
- Quick Installation Guide
If any items are missing or damaged, please contact your local D-Link reseller for assistance.
3. Product Overview
3.1 Front Panel
Figure 1: Front view of the DGS-1100-05V2 switch. This image displays the five Gigabit Ethernet ports, each with Link/Act and speed indicators, and the power LED.
The front panel of the DGS-1100-05V2 features five 10/100/1000 Mbps Gigabit Ethernet ports. Each port includes two LED indicators: a Link/Act LED (green) and a Speed LED (yellow for 1000 Mbps, orange for 10/100 Mbps). A power LED indicates the device's operational status.
3.2 Rear Panel
Figure 2: Rear view of the DGS-1100-05V2 switch. This image shows the DC power input (5V===1A), the recessed Reset button, and the SWITCH GND screw for grounding.
The rear panel includes the DC power input (5V===1A), a recessed Reset button for restoring factory defaults, and a grounding screw (SWITCH GND) for enhanced electrical safety.
4. Setup
4.1 Physical Installation
- Placement: Position the switch on a flat, stable surface or mount it using the provided kit. Ensure adequate ventilation around the device.
- Power Connection: Connect the provided power adapter to the DC power input on the rear panel of the switch, then plug the adapter into a suitable power outlet.
- Network Connections: Connect your network devices (computers, servers, access points, etc.) to the Gigabit Ethernet ports on the front panel using standard Ethernet cables (Cat5e or higher recommended).
- Grounding (Optional but Recommended): For enhanced safety, connect a grounding wire to the SWITCH GND screw on the rear panel and to a proper earth ground.
4.2 Initial Configuration
The DGS-1100-05V2 is a managed switch, allowing for advanced configuration via a web-based interface or the D-Link Network Assistant Utility.
- Connect to the Switch: Ensure your computer is connected to one of the switch's Ethernet ports.
- Obtain IP Address: By default, the switch may obtain an IP address via DHCP. If no DHCP server is present, it will use a default static IP address (refer to the Quick Installation Guide for the specific default IP).
- Access Web Interface: Open a web browser on your computer and enter the switch's IP address in the address bar. Log in using the default credentials (typically admin/admin, or as specified in the Quick Installation Guide).
- D-Link Network Assistant Utility: Alternatively, download and install the D-Link Network Assistant Utility from the D-Link support website. This utility can discover the switch on your network and provide a direct link to its web interface.
It is highly recommended to change the default administrator password immediately after initial login for security purposes.
5. Operating the Switch
The DGS-1100-05V2 offers a range of Layer 2 management features to optimize your network performance and security.
5.1 VLAN Support
Virtual Local Area Networks (VLANs) allow you to logically segment your network into separate broadcast domains. This can improve network security, reduce broadcast traffic, and simplify network management. The DGS-1100-05V2 supports 802.1Q tag-based VLANs and port-based VLANs. This feature is particularly useful for isolating different types of traffic, such as IP surveillance video streams, ensuring their priority and quality.
5.2 Quality of Service (QoS)
QoS allows you to prioritize network traffic, ensuring that critical applications (e.g., VoIP, video conferencing) receive sufficient bandwidth and minimal delay. The switch supports 802.1p CoS (Class of Service) and DSCP (Differentiated Services Code Point) based QoS, enabling you to define traffic priorities and manage bandwidth effectively.
5.3 IGMP Snooping
IGMP (Internet Group Management Protocol) Snooping optimizes multicast traffic delivery. By monitoring IGMP messages, the switch can intelligently forward multicast streams only to ports where devices have explicitly requested them, preventing unnecessary flooding of multicast traffic across the entire network and conserving bandwidth.
5.4 Energy Efficient Ethernet (EEE)
The DGS-1100-05V2 incorporates 802.3az Energy Efficient Ethernet (EEE) technology, also known as D-Link Green features. This allows the switch to automatically detect link status and cable length, adjusting power consumption accordingly. This helps reduce operating costs and environmental impact without compromising performance.
6. Maintenance
6.1 General Care
- Keep the switch in a cool, dry environment, away from direct sunlight and heat sources.
- Ensure proper ventilation and avoid blocking the ventilation holes.
- Clean the exterior of the switch with a soft, dry cloth. Do not use liquid or aerosol cleaners.
6.2 Firmware Updates
Periodically check the D-Link support website for firmware updates. Firmware updates can provide new features, performance enhancements, and security patches. Follow the instructions provided with the firmware update package carefully.
6.3 Factory Reset
If you encounter persistent issues or forget your login credentials, you can reset the switch to its factory default settings. To do this, use a paperclip or a similar pointed object to press and hold the recessed Reset button on the rear panel for approximately 5-10 seconds while the device is powered on. The switch will reboot with default settings.
7. Troubleshooting
| Problem | Possible Solution |
|---|---|
| No power LED indication. |
|
| No link light for a connected device. |
|
| Cannot access the web management interface. |
|
8. Specifications
| Feature | Detail |
|---|---|
| Model | DGS-1100-05V2 |
| Number of Ports | 5 Gigabit Ethernet (RJ45) |
| Data Transfer Rate | 10/100/1000 Mbps |
| Switching Capacity | 10 Gbps |
| Jumbo Frame Support | Up to 9216 bytes |
| VLAN Support | 802.1Q Tag-based, Port-based (up to 32 static VLANs) |
| QoS Support | 802.1p CoS, DSCP (4 queues per port) |
| Energy Efficiency | 802.3az Energy Efficient Ethernet (EEE) |
| Management | Web-based GUI, D-Link Network Assistant Utility |
| Fanless Design | Yes (0 dB) |
| Case Material | Metal |
| Product Dimensions (L x W x H) | 7.87" x 5.91" x 5.91" |
| Item Weight | 0.23 Kilograms (8.1 ounces) |
| Power Input | 5V===1A (DC) |
| Operating Temperature | 0°C to 40°C (32°F to 104°F) |
| Storage Temperature | -40°C to 70°C (-40°F to 158°F) |
| Operating Humidity | 10% to 90% non-condensing |
Note: Specifications are subject to change without notice. Please refer to the official D-Link website for the most current information.
9. Warranty and Support
9.1 Warranty Information
D-Link products are backed by a limited warranty. For specific warranty terms and conditions applicable to your region, please refer to the warranty card included with your product or visit the official D-Link website.
9.2 Technical Support
For technical assistance, product documentation, and software downloads, please visit the official D-Link support website. D-Link offers various support resources, including FAQs, troubleshooting guides, and driver downloads.
The D-Link Assist Next Business Day service provides additional peace of mind by replacing defective equipment quickly and efficiently. For details on this service, please consult the D-Link website or contact your local D-Link representative.
D-Link Support Website: www.dlink.com/support