Maxxima Cylinder LED Outdoor Wall Light (Model MEL-14125BW) Instruction Manual

1. Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your Maxxima Cylinder LED Outdoor Wall Light, Model MEL-14125BW. Please read this manual thoroughly before installation and retain it for future reference.

Figure 1: Maxxima Cylinder LED Outdoor Wall Light (Model MEL-14125BW).

2. Safety Information

WARNING: Risk of electric shock. Disconnect power at the fuse or circuit breaker before installing or servicing.

• All electrical connections must be in accordance with local codes, ordinances, or the National Electric Code (NEC).
• Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
• This fixture is intended for outdoor use and is suitable for wet locations.
• Do not attempt to alter the fixture or its components.
• Ensure the mounting surface is structurally sound to support the fixture.

3. Package Contents

Verify that all components are present before beginning installation:

• 1x Maxxima Cylinder LED Outdoor Wall Light (Model MEL-14125BW)
• Mounting Hardware (screws, wire connectors)
• 1x Sensor Cap (for disabling dusk-to-dawn function)
• Instruction Manual

4. Specifications

5. Installation Instructions

Before You Begin: Ensure power is disconnected at the circuit breaker or fuse box to prevent electric shock.

1. Prepare the Mounting Surface: Ensure the electrical junction box is securely mounted and the wiring is accessible.
2. Attach Mounting Bracket: Secure the provided mounting bracket to the junction box using the screws. Ensure the bracket is level.


Figure 2: Rear view of the fixture with mounting bracket and wiring.

3. Wire Connections:
   • Connect the green ground wire from the fixture to the house ground wire (usually bare copper or green) using a wire connector.
   • Connect the white fixture wire to the house neutral wire (usually white) using a wire connector.
   • Connect the black fixture wire to the house hot wire (usually black) using a wire connector.
   • Ensure all connections are secure.
4. Mount the Fixture: Carefully align the fixture with the mounting bracket and secure it using the provided screws. Ensure no wires are pinched.


Figure 3: Installed Maxxima Cylinder LED Outdoor Wall Light providing downlight.

5. Restore Power: Once the fixture is securely mounted and wired, restore power at the circuit breaker.

Installation Video Guide

Watch this video for a visual guide on installing the Maxxima Cylinder LED Outdoor Wall Sconce Light.

6. Operating Instructions

This fixture is equipped with a built-in dusk-to-dawn photocell sensor.

• Automatic Operation: The light will automatically turn on at dusk and turn off at dawn.
• Disabling Dusk-to-Dawn Function: If you prefer to control the light manually or use it in an indoor/up-directional setting, use the included sensor cap. Place the sensor cap over the photocell sensor located on the top of the fixture. This will keep the light on continuously when power is supplied.


Figure 4: View of the LED array and the photocell sensor on the top of the fixture.

7. Maintenance

To ensure optimal performance and appearance of your fixture:

• Cleaning: Clean the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents, as they may damage the finish or electrical components.
• Inspection: Periodically inspect the wiring and mounting for any signs of wear or damage.
• The integrated LED light source is designed for long-term use and is not user-replaceable.

8. Troubleshooting

If your light fixture is not operating correctly, refer to the following common issues:

• Light does not turn on:
  • Check if the power supply is active at the circuit breaker.
  • Ensure all wire connections are secure.
  • Verify the photocell sensor is not obstructed or covered if automatic operation is desired.
  • If the sensor cap is installed, remove it to test automatic operation.
• Light stays on during the day:
  • Ensure the photocell sensor is not obstructed by shadows or other light sources (e.g., another bright light fixture nearby).
  • If the sensor cap is installed, this is expected behavior. Remove the cap for dusk-to-dawn functionality.
• Light flickers:
  • Check for loose wire connections.
  • Ensure the voltage supply is stable.

If these steps do not resolve the issue, contact customer support.

9. Warranty

This Maxxima product is covered by a 3-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. For warranty claims or further details, please contact Maxxima customer support.

10. Customer Support

For technical assistance, troubleshooting, or warranty inquiries, please contact Maxxima customer support. Refer to the product packaging or the official Maxxima website for current contact information.

Visit the Maxxima Store on Amazon