1. Introduction
This user manual provides comprehensive instructions for the installation, operation, and maintenance of the BAYROL Automatic Salt AS5-191000. This device is designed to automatically maintain the disinfection and clarity of your pool water through salt electrolysis. Please read this manual carefully before operating the device to ensure safe and efficient use.
2. Safety Information
Always observe the following safety precautions to prevent injury or damage to the device:
- Ensure the device is installed by a qualified professional in accordance with local electrical and plumbing codes.
- Disconnect power to the unit before performing any maintenance or service.
- Keep all chemicals, including pool salt and pH-adjusting solutions, out of reach of children and pets.
- Wear appropriate personal protective equipment (PPE) when handling pool chemicals.
- Do not operate the device if it is damaged or malfunctioning. Contact customer support immediately.
- Ensure proper ventilation in the area where the device is installed.
3. Product Overview
The BAYROL Automatic Salt AS5-191000 is an advanced system for automated pool water treatment. It consists of a main control unit and an electrolysis cell, designed to convert salt into chlorine for disinfection.
Figure 3.1: The main control unit of the BAYROL Automatic Salt AS5-191000. This unit houses the electronic controls and display for managing the salt electrolysis process.
Figure 3.2: The BAYROL Automatic Salt AS5-191000 main unit shown alongside its electrolysis cell. The cell is where the salt-to-chlorine conversion takes place, and it connects directly into the pool's filtration system.
Figure 3.3: A complete view of the BAYROL Automatic Salt AS5-191000 system, including the main control unit, the electrolysis cell, and the flow switch. The flow switch ensures the system only operates when water is flowing through the cell, preventing damage.
4. Setup and Installation
Proper installation is crucial for the optimal performance and longevity of your BAYROL Automatic Salt AS5-191000. It is highly recommended that installation be performed by a certified pool technician.
4.1 Pre-Installation Checks
- Ensure your pool water has the correct salinity level as specified by BAYROL.
- Verify that the electrical supply meets the device's requirements.
- Confirm you have all necessary plumbing fittings and tools.
4.2 Installation Steps (General)
- Mounting the Control Unit: Select a dry, well-ventilated location near the pool's filtration system, away from direct sunlight and excessive heat. Securely mount the control unit to a wall using appropriate fasteners.
- Plumbing the Electrolysis Cell: Install the electrolysis cell into the pool's return line after the filter and heater. Ensure the flow direction matches the arrows on the cell. The flow switch should also be installed in line with the cell.
- Electrical Connection: Connect the control unit to a dedicated, grounded electrical outlet. Ensure all electrical connections are secure and waterproof.
- Sensor Connection: Connect any pH or ORP sensors (if applicable to your model) to the designated ports on the control unit and install them in the plumbing line according to the sensor's specific instructions.
4.3 Initial Startup
After installation, perform the following steps for initial startup:
- Ensure the pool pump is running and water is flowing through the electrolysis cell.
- Power on the BAYROL Automatic Salt AS5-191000 unit.
- Follow the on-screen prompts to configure initial settings, such as desired chlorine output and pool volume.
- It is essential to have precise water quality measurements. Consider using a reliable water testing kit or device.
- Ensure you have necessary chemicals like Bayrol pH-Minus Liquid Anti Calc available, as these are often required for optimal system performance and to prevent scaling on the cell.
5. Operating Instructions
The BAYROL Automatic Salt AS5-191000 is designed for automated operation, but regular monitoring is recommended.
5.1 Daily Operation
- The unit will automatically generate chlorine based on your set parameters and the pool's needs.
- Regularly check the device's screen for status updates and any alerts. This model does not feature Wi-Fi connectivity, so direct observation of the screen is necessary for monitoring.
- Ensure the pool pump is running for the required duration each day to allow for proper water circulation and chlorine distribution.
5.2 Adjusting Settings
Refer to the on-screen menu for adjusting settings such as chlorine output percentage or operating modes. Consult the detailed menu navigation in the full product manual for specific instructions.
6. Maintenance
Regular maintenance ensures the efficiency and longevity of your BAYROL Automatic Salt AS5-191000.
6.1 Electrolysis Cell Cleaning
Over time, calcium and other minerals can build up on the electrolysis cell plates, reducing efficiency. The frequency of cleaning depends on water hardness and usage.
- Turn off the power to the unit and the pool pump.
- Remove the electrolysis cell from the plumbing.
- Inspect the plates for scale buildup.
- If buildup is present, soak the cell in a mild acid solution (e.g., diluted muriatic acid or a commercial cell cleaning solution) following the solution's instructions. Always wear appropriate PPE and follow safety guidelines when handling acids.
- Rinse the cell thoroughly with fresh water before re-installing.
6.2 Water Chemistry Monitoring
Even with an automatic system, regular manual testing of pool water chemistry is vital. Monitor pH, alkalinity, calcium hardness, and salt levels weekly. Adjust as necessary to maintain optimal balance, which contributes to the system's effectiveness and prevents issues.
The product is designed for low maintenance, but consistent water balance checks are key.
7. Troubleshooting
This section addresses common issues you might encounter with your BAYROL Automatic Salt AS5-191000.
| Problem | Possible Cause | Solution |
|---|---|---|
| No chlorine production | Low salt level, dirty cell, low water flow, power issue. | Check salt level and add salt if needed. Clean the electrolysis cell. Ensure pool pump is running and flow switch is engaged. Verify power supply to the unit. |
| "Check Salt" or "Low Salt" indicator | Actual low salt, sensor issue, or cold water. | Test salt level manually and add salt if necessary. Ensure water temperature is within operating range. If problem persists, contact support. |
| Device not powering on | No power supply, tripped breaker, internal fault. | Check power outlet and circuit breaker. Ensure unit is properly plugged in. If still no power, contact a qualified technician. |
| Device malfunction after short period (e.g., less than a year) | Component failure, installation error, or manufacturing defect. | Contact the seller or manufacturer's customer support for diagnosis and potential repair or replacement. Be prepared to provide purchase details. |
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact BAYROL customer support or a certified service technician.
8. Specifications
Below are the technical specifications for the BAYROL Automatic Salt AS5-191000:
- Model Number: 191000
- Product Dimensions (L x W x H): 32.5 x 21 x 12 cm (12.8 x 8.3 x 4.7 inches)
- Item Weight: 4.3 kilograms (9.5 pounds)
- Power Source: Air-powered (Note: "Alimenté par l'Air" in source data might be a mistranslation for an electrical power source. Please refer to product packaging for exact power requirements.)
- Product Benefits: Maintains water disinfected and clear
- Item Form: Tablet, Granular (Note: "Comprimé, Granulaire" refers to associated chemical products, not the device itself.)
- Number of Items: 1
- Manufacturer: BAYROL
- ASIN: B08M6C7WZP
- Date First Available on Amazon.com.be: August 19, 2022
9. Warranty and Support
For warranty information, please refer to the documentation provided with your purchase or contact BAYROL directly. Warranty terms typically cover manufacturing defects for a specified period from the date of purchase.
If you experience any issues with your BAYROL Automatic Salt AS5-191000, or require technical assistance, please contact the seller from whom you purchased the product or BAYROL customer support. Be prepared to provide your product model number (AS5-191000 or 191000) and proof of purchase.
Some users have reported extended repair times and costs when dealing with certain sellers for repairs. It is advisable to verify the seller's return and repair policies before purchase, and to contact official BAYROL support channels if possible for complex issues.
