Smartwares 4-Channel Remote Control User Manual

Product Overview

The Smartwares SH4-90152 4-channel remote control is designed to conveniently switch your lights or other compatible devices on and off. It offers a reliable operating range of up to 30 meters and is fully compatible with any receiver from the Smartwares Plug & Connect series. This remote allows for individual control of up to four devices or the creation of four distinct device groups, all manageable with a simple button press. It also features a master button for controlling all connected devices simultaneously.

Image: Angled view of the Smartwares SH4-90152 4-channel remote control, showing the numbered buttons (1, 2, 3, 4, ALL) and ON/OFF buttons.

Key Features

• 4-Channel Control: Independently control up to four Plug & Connect receivers or groups of devices.
• Master Button: A dedicated "ALL" button allows for simultaneous control of all connected devices.
• Extended Range: Operates wirelessly with a radio frequency of 433.92 MHz, providing a signal range of up to 30 meters.
• Battery Powered: Powered by a replaceable CR2032 button cell battery (included).
• Plug & Connect Compatibility: Seamlessly integrates with all Smartwares Plug & Connect series receivers, enhancing home automation.
• Versatile Use: Suitable for controlling various devices such as roller shutters, lighting, and garage doors.

Setup and Installation

1. Battery Installation

The remote control comes with a pre-installed CR2032 button cell battery. If replacement is needed, follow these steps:

1. Locate the battery compartment cover on the back of the remote control.
2. Use a coin or small flat tool to turn the cover counter-clockwise to the "open" position.
3. Carefully remove the old CR2032 battery.
4. Insert a new CR2032 battery with the positive (+) side facing upwards.
5. Replace the cover and turn it clockwise to the "close" position until it clicks securely.

Image: Rear view of the remote control, highlighting the circular battery compartment with "open" and "close" indicators.

2. Pairing with Plug & Connect Receivers

To control your devices, the remote control must be paired with compatible Smartwares Plug & Connect receivers (sold separately). The pairing process typically involves the following steps, though specific receiver instructions may vary:

1. Ensure your Plug & Connect receiver is powered on and within range of the remote control (up to 30 meters).
2. Put the receiver into pairing mode. This usually involves pressing a learn button on the receiver itself. Refer to your receiver's manual for exact instructions.
3. While the receiver is in pairing mode, press the desired channel button (1, 2, 3, or 4) on the SH4-90152 remote control.
4. The receiver should indicate successful pairing (e.g., an LED light flashing or turning solid).
5. Repeat for each channel you wish to assign to different receivers or groups.

For detailed pairing instructions, always consult the user manual of your specific Smartwares Plug & Connect receiver.

Operating Instructions

The Smartwares SH4-90152 remote control is designed for straightforward operation of your connected devices.

Controlling Individual Devices or Groups

• Channel Buttons (1, 2, 3, 4): Each numbered button corresponds to a specific channel you have paired with a receiver or group of receivers.
• To turn on a device or group assigned to a channel, press the corresponding numbered button (e.g., "1") followed by the "ON" button.
• To turn off a device or group assigned to a channel, press the corresponding numbered button (e.g., "1") followed by the "OFF" button.

Master Control

• "ALL" Button: This button acts as a master control for all devices or groups paired with any of the four channels.
• To turn on all connected devices simultaneously, press the "ALL" button followed by the "ON" button.
• To turn off all connected devices simultaneously, press the "ALL" button followed by the "OFF" button.

Image: A hand holding the Smartwares remote control, illustrating its ergonomic design during use.

Maintenance

Battery Replacement

When the remote control's range decreases or it becomes unresponsive, it's likely time to replace the battery. Follow the "Battery Installation" steps in the Setup section to replace the CR2032 battery.

Always dispose of old batteries responsibly according to local regulations.

Cleaning

Wipe the remote control with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the surface.

Troubleshooting

Specifications

Warranty and Support

This product comes with a 1-year availability of spare parts. For further support, technical assistance, or warranty claims, please contact Smartwares customer service or refer to the official Smartwares website.

Please retain your proof of purchase for warranty purposes.