EZDIY-FAB US-white rgb slim fan with hub X-5P

EZDIY-FAB White Moonlight 120mm RGB Case Fan User Manual

Model: US-white rgb slim fan with hub X-5P | Brand: EZDIY-FAB

1. Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your EZDIY-FAB White Moonlight 120mm RGB Case Fan kit. Please read this manual thoroughly before installation and use to ensure proper functionality and safety.

2. Package Contents

Verify that all items listed below are included in your package:

120mm ARGB Case Fan (x6)
Fan Hub X (x1)
Remote Control (x1)
Screw Pack (x6)
User Manual (x1)

Diagram showing the contents of the EZDIY-FAB White Moonlight 120mm RGB Case Fan package, including six fans, a fan hub, a remote, screws, and a user manual. — Figure 2.1: Included components in the EZDIY-FAB White Moonlight 120mm RGB Case Fan kit.

3. Specifications

Feature	Detail
Size	120x120x25 mm (4.72"L x 0.98"W x 4.72"H)
Bearing Type	Hydraulic Bearing
Interface	6-Pin (proprietary to Fan Hub X)
Air Flow Capacity	32.7 CFM (Cubic Feet Per Minute)
Maximum Rotational Speed	1300 RPM
Noise Level	25 Decibels (typical)
Rated Voltage	12V/5V
Wattage	36 watts
Material	Polycarbonate, Rubber
RGB Sync	Motherboard 3-pin ARGB Header (5V, Di, -, G)

Diagram showing the dimensions and key specifications of the EZDIY-FAB 120mm fan, including size, bearing, interface, air flow, fan speed, noise level, and rated voltage. — Figure 3.1: Detailed specifications of the 120mm ARGB Case Fan.

Close-up diagram illustrating the dual light loop design of the fan, highlighting 8 LEDs in the central ring and 15 LEDs in the side ring for enhanced RGB effects. — Figure 3.2: Dual Light Loop design with central and side LEDs.

Exploded view diagram of the fan components, showing the hydraulic bearing motor, shock absorbing pads, ARGB ring, and special shape fan blade, emphasizing quiet operation. — Figure 3.3: Hydraulic Bearing for ultra-quiet operation.

4. Setup and Installation

4.1 Fan Hub X Installation

The Fan Hub X is essential for controlling multiple fans and their RGB lighting. It connects to your power supply and motherboard for power and ARGB synchronization.

Mount the Fan Hub X in a suitable location within your PC case, ensuring it is accessible for cable management.
Connect the SATA power cable from your power supply to the Fan Hub X.
Connect the 3-pin ARGB cable from the Fan Hub X to a compatible 5V 3-pin ARGB header on your motherboard (e.g., MSI/GIGABYTE +5V D G, ASUS +5V D_LED). Do NOT connect to a 12V 4-pin RGB header.
Connect each 120mm ARGB Case Fan to the 6-pin ports on the Fan Hub X. The Fan Hub X supports up to 6 fans.

Diagram illustrating the connection of the EZDIY-FAB Fan Hub X to a power supply via SATA and to a motherboard via a 5V 3-pin ARGB connector, with six fans connected to the hub. — Figure 4.1: Fan Hub X installation and connection diagram.

4.2 Fan Mounting

Mount the 120mm ARGB Case Fans in your desired locations within the PC case (e.g., front, top, rear, bottom) using the provided screws. Ensure proper airflow direction for optimal cooling.

Image showing multiple EZDIY-FAB White Moonlight 120mm RGB fans installed in a white PC case, illuminating the interior with vibrant colors. — Figure 4.2: Example of fans installed in a PC case.

5. Operating Instructions

5.1 Remote Control Functions

The included 21-key remote control allows for easy adjustment of fan speed, LED effects, colors, and brightness. There are two types of remote controls; you will receive one of them.

Diagram detailing the functions of two types of 21-key remote controls for the EZDIY-FAB RGB fans, showing buttons for LED on/off, fan speeds, static colors, lighting programs, brightness, sync to motherboard, and rainbow mode. — Figure 5.1: Remote Control Functions (Type-A and Type-B).

LED Switch ON/OFF: Turns the fan lighting on or off.
Low / Medium / High Fan Speeds: Adjusts the fan rotation speed.
Static Color Options: Selects a single static color for the LEDs.
Programmed Lighting Effects: Cycles through various pre-set lighting patterns.
Increase/Decrease Brightness: Adjusts the intensity of the LED lighting.
Light Change Speed: Modifies the speed of dynamic lighting effects.
Rainbow Mode: Activates a multi-color cycling effect.
Switch between Motherboard Sync and Remote Control: Hold the M/B button for 3 seconds to toggle between motherboard ARGB control and remote control.

5.2 Fan Speed Control

The remote control allows you to adjust fan speeds to balance cooling performance and noise levels. Choose between Low (500 RPM), Medium (900 RPM), and High (1300 RPM) settings.

Diagram showing three fan icons with different RPMs (500, 900, 1300) and a remote control, illustrating how to adjust fan speed to minimize noise or maximize airflow. — Figure 5.2: Fan speed adjustment options.

5.3 Motherboard ARGB Sync

If your motherboard has a compatible 5V 3-pin ARGB header, you can synchronize the fan lighting with your motherboard's software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome RGB). Ensure the Fan Hub X is connected to the correct header.

Diagram showing a 5V ARGB motherboard sync connection, highlighting the correct 3-pin header (5V, Di, -, G) and explicitly warning against connecting to a 12V RGB header. — Figure 5.3: Motherboard ARGB Sync connection details.

6. Maintenance

Regular maintenance ensures optimal performance and longevity of your fans.

Cleaning: Periodically clean the fan blades and frames to remove dust buildup. Use a soft, dry cloth or compressed air. Ensure the PC is powered off and unplugged before cleaning.
Anti-Vibration Pads: The fans are equipped with 8 anti-vibration rubber pads. Inspect these pads occasionally to ensure they are intact and effectively reducing noise and vibration.
Bearing: The self-lubricated hydraulic bearing is designed for long-term, quiet operation. No user lubrication is required.

Close-up image of the fan highlighting the low-noise design with 8 anti-vibration rubber pads on the corners of the fan frame. — Figure 6.1: Anti-vibration pads for reduced noise.

7. Troubleshooting

7.1 Fans Not Spinning

Ensure the Fan Hub X is correctly connected to the power supply via the SATA cable.
Verify that each fan is securely connected to a 6-pin port on the Fan Hub X.
Check if the remote control's fan speed setting is not set to off or minimum.

7.2 RGB Lighting Not Working or Incorrect

Confirm the Fan Hub X's ARGB cable is connected to a 5V 3-pin ARGB header on the motherboard, not a 12V 4-pin RGB header. Incorrect connection can damage the LEDs.
If using motherboard sync, ensure the remote control is switched to M/B sync mode (hold M/B button for 3 seconds).
Check your motherboard's ARGB software settings to ensure the lighting is enabled and configured correctly.
If using remote control, ensure the remote's battery is functional and the LED switch is ON.

7.3 Excessive Noise or Vibration

Ensure all fan mounting screws are tightened properly.
Check for any cables or obstructions touching the fan blades.
Verify that the anti-vibration pads are correctly positioned and not damaged.
Reduce fan speed using the remote control if noise persists.

8. Warranty and Support

EZDIY-FAB products typically come with a manufacturer's warranty. For specific warranty details, please refer to the warranty card included with your product or visit the official EZDIY-FAB website. For technical support or customer service, please contact EZDIY-FAB directly through their official channels.

Contact Information:

Website: www.ezdiy-fab.com
Email: Refer to product packaging or website for support email.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.