1. Introduction
Thank you for choosing the Stiga ST4262P Two-Stage Snow Blower. This manual provides essential information for the safe and efficient operation, maintenance, and storage of your snow blower. Please read this manual thoroughly before assembly, operation, or maintenance to ensure proper use and to prevent injury or damage.
The Stiga ST4262P is designed for reliable and robust snow clearing in medium to large areas, capable of handling snow up to 50 cm deep. It features a powerful 208 cc engine with electric start, a 62 cm clearing width, and a two-stage auger system.
Image 1: The Stiga ST4262P Two-Stage Snow Blower, showcasing its robust design, large wheels, and front auger system.
1.1 General Safety Information
Always prioritize safety. Familiarize yourself with all controls and safety decals before operating the machine. Wear appropriate personal protective equipment (PPE), including eye protection, hearing protection, and sturdy footwear. Keep bystanders, especially children and pets, away from the operating area.
2. Setup and Assembly
2.1 Unpacking
Carefully remove all components from the packaging. Inspect for any shipping damage. Retain packaging materials until you are satisfied with the product.
2.2 Handlebar Assembly
Attach the handlebar assembly to the main unit using the provided hardware. Ensure all bolts are securely tightened. Refer to the assembly diagrams in the separate assembly guide for detailed steps.
2.3 Fuel and Oil
The ST4262P is equipped with a 4-stroke engine. It requires unleaded gasoline and separate engine oil. Do not mix oil with gasoline.
- Engine Oil: Fill the engine crankcase with the recommended 4-stroke engine oil (e.g., SAE 5W-30 or 10W-30, depending on ambient temperature). Check the oil level using the dipstick; do not overfill.
- Fuel: Fill the fuel tank with fresh, unleaded gasoline. Avoid spilling fuel. Always refuel in a well-ventilated area with the engine off and cool.
2.4 Initial Checks
- Verify tire pressure for optimal traction.
- Ensure all control levers and cables operate smoothly.
- Check that the auger and impeller are free of obstructions.
3. Operating Instructions
3.1 Starting the Engine
The ST4262P features a 220V electric start for convenience, in addition to a recoil starter.
- Ensure the fuel valve is open and the ignition key is inserted.
- Set the choke lever to the 'FULL CHOKE' position for a cold engine.
- Connect the power cord to the electric start port and a 220V outlet.
- Press and hold the electric start button until the engine starts.
- Once the engine starts, disconnect the power cord and gradually move the choke lever to the 'RUN' position as the engine warms up.
- Alternatively, use the recoil starter by pulling the starter rope firmly.
3.2 Controls
- Drive Lever: Engages the wheel drive. The snow blower has 6 forward speeds and 2 reverse speeds. Select the appropriate speed based on snow conditions.
- Auger Engagement Lever: Engages the auger and impeller to clear snow.
- Chute Rotation Control: Adjusts the direction of snow discharge. This can be adjusted directly from the control panel.
- Deflector Tilt Control: Adjusts the height and distance of snow discharge. This can also be adjusted from the control panel.
3.3 Snow Clearing Techniques
Operate the snow blower at a steady pace. For deep or heavy snow, take narrower passes. Overloading the machine can reduce performance and cause damage. Always direct discharged snow away from people, windows, and vehicles.
4. Maintenance
Regular maintenance ensures the longevity and optimal performance of your Stiga ST4262P snow blower. Always turn off the engine, remove the ignition key, and disconnect the spark plug wire before performing any maintenance.
4.1 After Each Use
- Clean snow and ice from the auger housing, chute, and engine.
- Inspect shear pins for damage and replace if necessary.
- Check for loose fasteners and tighten as needed.
4.2 Seasonal Maintenance
- Engine Oil Change: Change the engine oil after the first 5 hours of operation, then every 25-50 hours or annually.
- Spark Plug: Inspect and clean the spark plug annually. Replace if worn or fouled.
- Belts: Inspect drive and auger belts for wear or damage. Replace if necessary.
- Skid Shoes: Check skid shoes for wear and adjust or replace to maintain proper clearing height.
4.3 Storage
Before storing the snow blower for an extended period:
- Drain the fuel tank or add a fuel stabilizer. Run the engine until it stops to consume all fuel in the carburetor.
- Clean the entire machine thoroughly.
- Change the engine oil.
- Store in a clean, dry area, away from direct sunlight and extreme temperatures.
5. Troubleshooting
This section addresses common issues you might encounter with your snow blower.
| Problem | Possible Cause | Solution |
|---|---|---|
| Engine won't start | No fuel; old fuel; spark plug issue; choke setting incorrect | Check fuel level; use fresh fuel; inspect/replace spark plug; adjust choke |
| Poor snow throwing | Clogged chute; worn auger/impeller; loose belt | Clear chute (engine off!); inspect/replace auger/impeller; check/tighten belt |
| Loss of drive | Drive belt worn or broken; linkage issue | Inspect/replace drive belt; check linkage for obstructions |
If you encounter problems not listed here or if solutions do not resolve the issue, please contact authorized service personnel.
6. Specifications
| Feature | Specification |
|---|---|
| Model | ST4262P |
| Engine Type | 4-stroke |
| Engine Displacement | 208 cc |
| Engine Power | 6 HP |
| Starting System | Electric (220V) / Recoil |
| Clearing Width | 62 cm |
| Max. Snow Depth | 50 cm |
| Throwing Distance | Up to 9 meters |
| Drive Speeds | 6 Forward / 2 Reverse |
| Tires | 14" Snow Hog tread |
| Product Dimensions (L x W x H) | 5 x 10 x 106 cm |
| Weight | 95 kg |
| Manufacturer Reference | 18-2841-31 |
7. Warranty and Support
7.1 Warranty Information
Your Stiga ST4262P snow blower is covered by a manufacturer's warranty against defects in materials and workmanship. Please refer to the separate warranty document included with your purchase for specific terms, conditions, and duration. Keep your proof of purchase for warranty claims.
7.2 Customer Support
For technical assistance, spare parts, or service, please contact your authorized Stiga dealer or visit the official Stiga website. When contacting support, please have your model number (ST4262P) and serial number ready.
