CREATE NETBOT S15 2.0 Robot Vacuum Cleaner Replacement Kit Instruction Manual

1. Product Overview

This replacement kit is designed for the CREATE NETBOT S15 2.0 robot vacuum cleaner. It provides essential components to maintain optimal cleaning performance and extend the lifespan of your device. Regular replacement of these parts ensures efficient dust collection and air filtration.

Kit Contents:

• 6 Side Brushes (3 left, 3 right)
• 1 Central Rotating Brush
• 2 HEPA Filters
• 4 Microfiber Mops

Image 1.1: Overview of the CREATE NETBOT S15 2.0 Replacement Kit, showing side brushes, central brush, HEPA filters, and microfiber mops.

2. Components and Their Function

2.1 Side Brushes

The side brushes are crucial for sweeping dust and debris from edges and corners towards the central brush, ensuring thorough cleaning. This kit includes 6 side brushes (3 left-rotating and 3 right-rotating) for replacement.

Image 2.1: Two individual side brushes, one designed for left rotation and one for right rotation, featuring three bristles each.

2.2 Central Rotating Brush

The central rotating brush is specifically designed to agitate and lift dirt particles, dust, and pet hair from various floor surfaces, directing them into the vacuum's suction inlet.

Image 2.2: The central rotating brush, featuring a spiral design with bristles and rubber fins for effective debris collection.

2.3 HEPA Filters

HEPA (High-Efficiency Particulate Air) filters are composed of a randomly arranged network of fibers designed to capture microscopic particles. These filters prevent the passage of contaminating dust particles, germs, dust mites, and pollen, improving air quality.

Image 2.3: A set of two HEPA filters, each consisting of a pleated white filter element and a black foam pre-filter.

2.4 Microfiber Mops

The microfiber mops are designed for wet cleaning. They feature an electrostatic charge to trap even the smallest dust particles, providing a thorough wipe on hard floors.

Image 2.4: A single green microfiber mop pad, designed to attach to the robot vacuum for wet cleaning.

3. Installation Instructions

Before performing any installation or replacement, ensure your NETBOT S15 2.0 robot vacuum cleaner is turned off and disconnected from its charging base.

3.1 Replacing Side Brushes

1. Turn the robot vacuum cleaner upside down.
2. Locate the side brushes. Each brush is typically held by a screw.
3. Using a screwdriver, carefully remove the screw holding the old side brush.
4. Remove the old brush.
5. Align the new side brush (ensure you use the correct left/right brush if specified by your robot model) with the mounting post.
6. Secure the new brush with the screw.

3.2 Replacing the Central Rotating Brush

1. Turn the robot vacuum cleaner upside down.
2. Locate the brush guard cover, usually secured by clips or screws.
3. Open or remove the brush guard cover.
4. Lift out the old central rotating brush.
5. Clean any hair or debris from the brush compartment.
6. Insert the new central rotating brush, ensuring its ends fit correctly into the designated slots.
7. Close or reattach the brush guard cover.

3.3 Replacing HEPA Filters

1. Open the dustbin compartment of your robot vacuum cleaner.
2. Remove the dustbin.
3. Locate the filter assembly within the dustbin.
4. Remove the old HEPA filter and any pre-filter.
5. Insert the new HEPA filter and pre-filter (if applicable) into the dustbin, ensuring a snug fit.
6. Reinsert the dustbin into the robot vacuum cleaner and close the compartment.

3.4 Attaching/Replacing Microfiber Mops

1. Locate the mop attachment plate on the underside of your robot vacuum cleaner.
2. If replacing, remove the old microfiber mop from the plate (it may be attached with Velcro or clips).
3. Attach a clean microfiber mop to the mop attachment plate, ensuring it is securely fastened.
4. Fill the water tank (if your model has one) and attach the mop plate to the robot.

4. Maintenance and Replacement Schedule

Regular maintenance and timely replacement of these components are essential for your robot vacuum's performance and longevity. The following are general guidelines; actual replacement frequency may vary based on usage and environment.

4.1 Side Brushes

• Inspection: Check weekly for wear, bending, or entanglement with hair.
• Replacement: Replace every 3-6 months, or sooner if visibly damaged or worn.

4.2 Central Rotating Brush

• Cleaning: Clean weekly by removing tangled hair and debris. A cleaning tool (often included with the robot) can assist.
• Replacement: Replace every 6-12 months, or if bristles are significantly worn or damaged.

4.3 HEPA Filters

• Cleaning: Tap filters gently over a trash can to remove dust after each use or weekly. Do not wash HEPA filters with water unless explicitly stated by the manufacturer.
• Replacement: Replace every 2-3 months to maintain optimal filtration efficiency and prevent reduced suction power.

4.4 Microfiber Mops

• Cleaning: Wash after each use. They can typically be hand-washed or machine-washed with mild detergent. Air dry completely before reattaching.
• Replacement: Replace every 1-3 months, or when they show signs of wear, reduced absorbency, or persistent staining.

5. Troubleshooting Common Issues

This section addresses common issues related to the replacement parts. For general robot vacuum troubleshooting, refer to your robot's main instruction manual.

5.1 Reduced Cleaning Performance

• Cause: Worn side brushes, clogged central brush, or dirty/clogged HEPA filter.
• Solution: Inspect side brushes for damage and replace if necessary. Clean the central brush of tangled hair and debris. Replace HEPA filters if they are visibly dirty or if suction power has decreased.

5.2 Unusual Noises During Operation

• Cause: Debris caught in the central brush or side brushes, or improperly installed brushes.
• Solution: Turn off the robot and inspect the central brush and side brushes for any foreign objects (e.g., string, hair). Remove any obstructions. Ensure all brushes are correctly installed and secured.

5.3 Mop Not Effectively Cleaning

• Cause: Dirty or worn microfiber mop.
• Solution: Remove and wash the microfiber mop. If it remains ineffective after washing or shows significant wear, replace it with a new one. Ensure the water tank (if applicable) is filled.

6. Specifications

7. Warranty and Support

Information regarding specific warranty terms for this replacement kit is not provided in the product data. For any support inquiries or questions about your CREATE NETBOT S15 2.0 robot vacuum cleaner or its replacement parts, please refer to the original product manual or contact CREATE customer service directly.

You may find contact information on the official CREATE website or through your point of purchase.