Adalene 10 Inch Large Atomic Wall Clock Model 218 Instruction Manual

1. Introduction

Thank you for choosing the Adalene 10 Inch Large Atomic Wall Clock. This clock is designed to provide accurate timekeeping by automatically synchronizing with the WWVB radio signal broadcast from Fort Collins, Colorado. This manual provides essential information for setting up, operating, and maintaining your new atomic wall clock.

Image 1.1: Front view of the Adalene 10 Inch Large Atomic Wall Clock. The clock features a black frame, a white dial with clear black Arabic numerals, and black hour, minute, and second hands.

2. Safety Information

• Do not expose the clock to extreme temperatures, direct sunlight, or high humidity.
• Use only the specified battery type (1 AA battery).
• Do not mix old and new batteries, or different types of batteries.
• Remove batteries if the clock will not be used for an extended period to prevent leakage.
• Keep batteries out of reach of children.

3. Package Contents

• 1 x Adalene 10 Inch Large Atomic Wall Clock
• 1 x Instruction Manual

4. Setup

4.1 Battery Installation

1. Locate the battery compartment on the back of the clock.
2. Insert one (1) new AA alkaline battery, ensuring the correct polarity (+ and -) as indicated inside the compartment.
3. Once the battery is inserted, the clock hands will automatically move to the 12 o'clock position and then begin searching for the WWVB atomic signal.

4.2 Initial Atomic Time Synchronization

The clock will attempt to receive the WWVB radio signal from Fort Collins, Colorado. This process can take several hours, especially if the signal is weak or if there is interference. For best reception:

• Place the clock near a window, ideally facing towards Colorado.
• Avoid placing the clock near electronic devices, metal structures, or large appliances that may cause interference.
• Allow the clock to sit undisturbed overnight for optimal signal reception.

4.3 Time Zone and DST Settings

Image 4.1: Back view of the Adalene 10 Inch Large Atomic Wall Clock. This image displays the battery compartment, a time zone switch, and a Daylight Saving Time (DST) switch. There are also two small red buttons, likely for reset and manual time adjustment.

On the back of the clock, you will find switches for Time Zone and Daylight Saving Time (DST).

• Time Zone Switch: Set this switch to your local time zone (e.g., PST for Pacific Standard Time, MST for Mountain Standard Time, CST for Central Standard Time, EST for Eastern Standard Time).
• DST Switch: If your region observes Daylight Saving Time, set this switch to the 'ON' position. If your region does not observe DST (e.g., Arizona), set it to 'OFF'.

After setting these switches, the clock will continue its attempt to synchronize with the atomic signal and display the correct time for your selected zone, including automatic DST adjustments.

5. Operating the Clock

Once the Adalene Atomic Wall Clock has successfully synchronized with the WWVB signal and your time zone and DST settings are configured, it will operate automatically. The clock will:

• Maintain precise timekeeping by regularly receiving the atomic signal.
• Automatically adjust for Daylight Saving Time changes (if the DST switch is set to 'ON').

5.1 Manual Time Setting (If Needed)

In rare cases, if the clock fails to synchronize after an extended period, or if you need to set the time manually for any reason, you can use the manual setting buttons located on the back of the clock. Refer to the troubleshooting section for guidance on manual adjustment.

6. Maintenance

6.1 Cleaning

To clean your clock, use a soft, dry cloth. Do not use abrasive cleaners, solvents, or chemical sprays, as these can damage the clock's finish or internal components.

6.2 Battery Replacement

Replace the AA battery annually or when the clock hands stop moving or appear to be losing time. Always use a fresh, high-quality alkaline battery. Follow the battery installation steps in Section 4.1.

7. Troubleshooting

7.1 Resetting the Clock

If the clock is not functioning as expected, you can perform a reset. Locate the 'RESET' button on the back of the clock (often a small, recessed button). Use a pointed object (like a pen tip) to press and hold the button for a few seconds. This will reset the clock and initiate a new atomic signal search.

8. Specifications

Image 8.1: Adalene 10 Inch Large Atomic Wall Clock with dimensions. The image shows the clock's diameter as 10 inches.

9. Warranty and Support

Adalene products are manufactured with quality and care. This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty details, support, or service inquiries, please refer to the product packaging or contact Adalene customer service through the retailer where the product was purchased.