BONTEC Dual Monitor Stand Riser

Introduction

The BONTEC Dual Monitor Stand Riser is designed to enhance your workspace ergonomics and organization. This versatile stand elevates your monitors to an optimal viewing height, reducing strain on your neck and back. Its adjustable length and swivel angles allow for a customized setup, while integrated storage compartments and cable management features help maintain a tidy desk environment.

Image: The BONTEC Dual Monitor Stand Riser in a typical setup, supporting two monitors and providing under-shelf storage.

Safety Information

• Ensure all components are securely fastened before placing monitors or other items on the stand.
• Do not exceed the maximum load capacity of 44 pounds (20 kg).
• Place the stand on a stable, level surface to prevent tipping.
• Keep small parts away from children to avoid choking hazards.
• Avoid exposing the stand to excessive moisture or direct sunlight.

Package Contents

Please verify that all the following components are included in your package:

• Monitor Stand (Engineered Wood components)
• Assembly Screws
• Dowel Pins
• Screwdriver (for assembly)
• Non-slip Pads
• Cable Management Clip

Setup

Assembly of the BONTEC Dual Monitor Stand Riser is straightforward and typically takes about 3 minutes. Follow these steps:

1. Prepare Components: Lay out all wooden panels, screws, and dowel pins. Identify the main center section and the two adjustable side sections.
2. Assemble Side Sections: For each side section, insert the dowel pins into the pre-drilled holes on the bottom panel. Align the side panels with the dowel pins and screw holes. Secure the side panels to the bottom panel using the provided screws and screwdriver.


Image: Step-by-step visual guide for assembling the monitor stand sections using screws and dowel pins.

3. Connect Sections: Once the two side sections are assembled, position them on either side of the central section. The design allows for adjustable length and angle.
4. Apply Non-slip Pads: Attach the provided non-slip pads to the bottom of each stand section to prevent scratching your desk surface and ensure stability.


Image: Detail of the non-slip pads on the bottom of the stand, designed to protect your desk.

Assembly Video Guide

Operating the Stand

The BONTEC Dual Monitor Stand Riser offers several features for an optimized workspace:

• Adjustable Length: The stand's length can be adjusted from 31.5 inches to 42.5 inches by sliding the side sections. This allows it to fit various desk sizes and accommodate different monitor setups.
• Swivel Angle: The two side sections can be swiveled to create a straight, angled, or V-shaped configuration, providing flexibility for your viewing preference and desk layout.
• Ergonomic Height: By raising your monitors to eye level, the stand helps to reduce neck, back, and shoulder strain, promoting a healthier posture during long periods of use.
• Integrated Storage: Utilize the space underneath the stand to store your keyboard, mouse, laptop, files, or other office essentials, keeping your desktop clear and organized.
• Smartphone Holder: A dedicated slot is provided to hold your smartphone upright for easy viewing and access.
• Cable Management: An opening and included clip assist in routing and organizing cables, preventing clutter and tangles.

Image: Illustrations demonstrating the adjustable length and swivel angle capabilities of the stand.

Image: Visual comparison of posture before and after using the ergonomic monitor stand.

Image: Close-up views of the integrated smartphone holder and cable management system.

Product Features Video

Maintenance

To ensure the longevity and appearance of your BONTEC Dual Monitor Stand Riser, follow these simple maintenance guidelines:

• Cleaning: Wipe the surface with a soft, damp cloth. For stubborn marks, a mild soap solution can be used, followed by drying with a clean cloth. Avoid abrasive cleaners or harsh chemicals.
• Dusting: Regularly dust the stand to prevent accumulation, which can dull the finish.
• Inspection: Periodically check all screws and connections to ensure they remain tight. Retighten if necessary.
• Avoid Overloading: Do not place items heavier than the specified load capacity on the stand.

Image: The stand's surface is easy to clean with a damp cloth.

Troubleshooting

If you encounter any issues with your monitor stand, please refer to the following common solutions:

• Stand is Wobbly: Ensure all assembly screws are fully tightened. Check that the stand is placed on a flat, stable surface. Verify that the non-slip pads are correctly applied to all contact points.
• Difficulty Adjusting Length/Angle: Ensure no objects are obstructing the sliding or swiveling mechanism. Apply gentle, even pressure when adjusting.
• Scratches on Desk: Confirm that the non-slip pads are properly installed and intact. If pads are worn, contact customer support for replacements.
• Items Sliding Off: Ensure the stand is level and not tilted. Do not overload the stand beyond its weight capacity.

Specifications

Warranty and Support

BONTEC products are designed for durability and user satisfaction. For specific warranty details, please refer to the product packaging or contact BONTEC customer support.

For additional assistance, troubleshooting, or to download the full installation manual, please visit the official BONTEC website or refer to the provided PDF document:

• Official User Guide (PDF): Download Installation Manual
• BONTEC Store: Visit the BONTEC Store on Amazon