Fujitsu General UTR-FA16-2K

Download PDFFree PDF. The Save button below keeps a bookmark and private notes in your account.

Fujitsu General UTR-FA16-2K Mini Split Ductless Filter Instruction Manual

1. Introduction

This manual provides essential information for the installation, maintenance, and proper use of your Fujitsu General UTR-FA16-2K Mini Split Ductless Filter. This filter is designed to improve air quality by capturing dust and other airborne particles within compatible Fujitsu mini split indoor units. Please read these instructions carefully before proceeding.

Two Fujitsu UTR-FA16-2K mini split ductless filters, showing dimensions of 8-1/4 inches in length and 1-3/8 inches in width.

Image 1: Fujitsu UTR-FA16-2K Filters with dimensions.

2. Product Compatibility

The Fujitsu UTR-FA16-2K (K9315361042) replacement filter is compatible with the following Fujitsu mini split indoor unit models:

  • ASU12RL
  • ASU12RLF
  • ASU12RLF1
  • ASU12RLS2
  • ASU12RLS3
  • ASU12RLS3Y
  • ASU15RLF1
  • ASU15RLS
  • ASU15RLS2
  • ASU15RLS3
  • ASU15RLSY3
  • ASU7RLF
  • ASU7RLF1
  • ASU9RL
  • ASU9RLF
  • ASU9RLF1
  • ASU9RLS2
  • ASU9RLS3
  • ASU9RLS3Y
A red and white graphic displaying the Fujitsu logo and a list of compatible mini split unit models for the K9315361042 filter.

Image 2: List of compatible Fujitsu Mini Split Units.

3. Setup and Installation

Follow these steps to install or replace your Fujitsu UTR-FA16-2K filter:

  1. Power Off: Before beginning, ensure your mini split unit is powered off at the circuit breaker to prevent accidental operation.
  2. Open Unit Cover: Carefully open the front cover of your indoor mini split unit. Refer to your mini split unit's manual for specific instructions on opening the cover.
  3. Locate Filter Slot: Identify the filter slots within the unit. The UTR-FA16-2K filters are typically inserted into a designated frame or slot.
  4. Remove Old Filters: If replacing existing filters, gently slide out the old filters from their slots. Dispose of used filters responsibly.
  5. Insert New Filters: Take a new Fujitsu UTR-FA16-2K filter. Align it with the filter slot and slide it in until it is securely seated. Ensure the filter is oriented correctly according to any markings on the filter or unit.
  6. Close Unit Cover: Once both filters are installed, carefully close the front cover of your mini split unit until it latches securely.
  7. Restore Power: Turn the power back on at the circuit breaker.
Diagram showing the process of inserting a new filter into a mini split unit's filter frame.

Image 3: Filter installation diagram.

4. Operating Instructions

Once installed, the Fujitsu UTR-FA16-2K filter operates passively to purify the air passing through your mini split unit. No additional user interaction is required for its operation. Ensure your mini split unit is running in its normal operating modes for the filter to function effectively.

5. Maintenance

Regular maintenance of your Fujitsu UTR-FA16-2K filter is crucial for optimal performance and air quality.

  • Cleaning: It is recommended to clean the filter every three months.
    • Gently clean the filter in warm water with a mild detergent.
    • Do not scrub the air filter with an abrasive pad or brush, as this can damage the filter material.
    • Allow the filter to air dry completely before re-installing it into the unit.
  • Replacement: The filter should be replaced every three years to maintain its effectiveness. This package includes two filters, allowing for one replacement.

6. Troubleshooting

If you experience reduced air quality or airflow after installing the filter, consider the following:

  • Incorrect Installation: Verify that the filters are correctly seated in their slots and that the mini split unit cover is fully closed.
  • Clogged Filters: If it has been more than three months since the last cleaning, or three years since replacement, the filters may be clogged. Clean or replace them as per the maintenance schedule.
  • Unit Malfunction: If issues persist, the problem may not be related to the filter. Consult your Fujitsu mini split unit's instruction manual or contact a qualified technician for further diagnosis.

7. Specifications

Model NumberUTR-FA16-2K (K9315361042)
Dimensions (Each Filter)8.25 inches (Height) x 1.375 inches (Width) x 0.1875 inches (Depth)
MaterialPlastic
Package Contents2 x Fujitsu UTR-FA16-2K Filters
Recommended Cleaning IntervalEvery 3 months
Recommended Replacement IntervalEvery 3 years

8. Warranty and Support

For specific warranty information regarding your Fujitsu UTR-FA16-2K filters, please refer to the documentation provided with your original Fujitsu mini split unit or contact Fujitsu General customer support directly. Ensure you purchase genuine Fujitsu replacement parts to maintain warranty validity and optimal performance.

For further assistance or technical support, please visit the official Fujitsu General website or contact their customer service department.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.