1. Introduction
This manual provides detailed instructions for the proper installation, operation, and maintenance of your Kimberly-Clark Professional Electronic Hard Roll Towel Dispenser, model 49807. Please read this manual thoroughly before using the dispenser to ensure safe and efficient operation. This dispenser is designed for commercial use, providing touchless paper towel dispensing for improved hygiene.
2. Safety Information
- Always ensure the dispenser is securely mounted to a stable wall surface before use.
- Use only the specified type and size of hard roll paper towels.
- Do not expose the dispenser to excessive moisture or direct water spray.
- Keep hands and foreign objects clear of the paper exit slot during operation.
- Battery replacement should be performed by an adult. Dispose of used batteries responsibly.
- Do not attempt to modify or repair the dispenser yourself. Contact qualified service personnel for assistance.
3. Package Contents
Verify that all items are present in the package:
- Kimberly-Clark Professional Electronic Hard Roll Towel Dispenser (Model 49807)
- Mounting Hardware (screws, anchors)
- Dispenser Key
- Batteries (if included, check packaging)
- Instruction Manual
4. Setup and Installation
4.1 Wall Mounting
- Select a suitable wall location, ensuring adequate clearance for operation and maintenance.
- Open the dispenser cover using the provided key.
- Hold the dispenser against the wall at the desired height and mark the mounting holes.
- Drill pilot holes at the marked locations. Insert wall anchors if necessary.
- Secure the dispenser to the wall using the provided screws. Ensure it is firmly attached.
4.2 Battery Installation
- Locate the battery compartment inside the dispenser.
- Insert the required batteries (typically D-cell, refer to dispenser label for exact type and quantity) according to the polarity indicators (+/-).
- Close the battery compartment cover securely.
4.3 Loading Paper Towels

Image: The Kimberly-Clark Professional Electronic Hard Roll Towel Dispenser shown open, revealing the internal mechanism for loading a paper towel roll and the battery compartment area.
- Open the dispenser cover using the key.
- Place a new hard roll towel onto the roll holders, ensuring it spins freely.
- Feed the leading edge of the paper towel into the feed mechanism slot until it engages.
- Close the dispenser cover and lock it with the key.
5. Operating Instructions
The Kimberly-Clark Professional Electronic Hard Roll Towel Dispenser operates automatically using a sensor.
- Ensure the dispenser is properly loaded with a paper towel roll and has fresh batteries.
- Place your hand approximately 1-2 inches below the sensor area (typically indicated by "PLACE HAND BELOW" or similar marking).
- The dispenser will automatically present a pre-measured length of paper towel.
- Grasp the towel and pull downwards to tear it off.
- The dispenser will be ready to dispense the next towel after a brief delay.
6. Maintenance
6.1 Cleaning
- Clean the exterior of the dispenser regularly with a soft, damp cloth and mild soap.
- Do not use abrasive cleaners or solvents, as these can damage the finish.
- Periodically wipe the sensor lens with a clean, dry cloth to ensure proper operation.
6.2 Paper Roll Replacement
When the paper roll is depleted or nearly depleted:
- Unlock and open the dispenser cover.
- Remove the empty roll core.
- Install a new hard roll towel as described in Section 4.3.
- Close and lock the dispenser cover.
6.3 Battery Replacement
Replace batteries when the low battery indicator (if present) illuminates, or when dispensing becomes inconsistent or stops.
- Unlock and open the dispenser cover.
- Open the battery compartment.
- Remove old batteries and dispose of them properly.
- Insert new batteries, ensuring correct polarity.
- Close the battery compartment and dispenser cover, then lock it.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Dispenser does not dispense towel. | No power (dead batteries). Paper roll empty or improperly loaded. Sensor obstructed or dirty. | Replace batteries. Load new paper roll correctly. Clean sensor lens. |
| Towel dispenses too short or too long. | Internal settings may need adjustment (if applicable). | Consult Kimberly-Clark support for specific adjustment procedures. |
| Paper jam. | Improper paper loading. Incorrect paper type. | Open dispenser, clear jam, reload paper correctly. Ensure compatible paper is used. |
| Dispenser makes unusual noise. | Internal mechanism issue. | Contact Kimberly-Clark support. Do not attempt to force operation. |
8. Specifications
- Brand: Kimberly-Clark
- Model: 49807
- Product Type: Electronic Hard Roll Towel Dispenser
- Color: White
- Mounting Type: Wall Mount
- Item Weight: Approximately 3.65 kg (3 kg 650 g)
- Product Dimensions (LxWxH): Approximately 3.6 x 2.6 x 2.66 Meters (360 x 260 x 266 cm)
- Batteries Included: Yes (check packaging for type and quantity)
- Compatibility: Designed for Hard Roll Towels, compatible with Scott 1005 HRT Roll
9. Warranty and Support
For warranty information, specific product support, or to order spare parts, please contact Kimberly-Clark Professional directly.
Support Contact: 1-800-246-4652
Please have your model number (49807) and purchase details available when contacting support.