Model: B08K7HG8SV
This manual provides detailed instructions for the installation, operation, and maintenance of your BANVIE Universal Car Security Alarm System. This system is designed to enhance vehicle security with features such as remote arming/disarming, shock sensor detection, central locking automation, and anti-hijacking capabilities. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Image: Visual representation of the system's key features in action.
Installation of this car security system requires technical knowledge of vehicle electrical systems. Professional installation is highly recommended to ensure correct wiring and optimal performance. Incorrect installation can lead to system malfunction or damage to your vehicle.
Image: The main control unit of the BANVIE car alarm system, showing its compact design and connection ports.
The main unit is the central control module for the alarm system. Ensure it is mounted securely in a hidden, dry location within the vehicle, away from direct heat or moisture.
Image: A compact remote control for the alarm system, with dimensions indicated.
The system includes two remote transmitters for convenient control. Keep them secure and away from unauthorized access.
Image: The 6-tone siren, designed to produce loud alarm sounds.
Mount the siren in the engine bay, facing downwards to prevent water accumulation, and away from excessive heat. Ensure it is securely fastened and its wiring is protected.
Image: Comprehensive wiring diagram illustrating all necessary connections for the alarm system.
Refer to the provided wiring diagram for all electrical connections. Pay close attention to power, ground, ignition (ACC), door triggers, trunk trigger, hood trigger, central locking wires, and siren connections. Ensure all connections are secure and properly insulated.
Press the lock button once on the remote transmitter. The siren will chirp once, and the vehicle's flash lights will gleam once. The central door locking system will engage automatically. If a window closer module is installed, power windows will roll up within 30 seconds. After 8 seconds, the LED indicator will flash, signifying the system is armed. In this state, the shock sensor, door, hood, and ACC (ignition) inputs are actively monitored.
Press the unlock button once on the remote transmitter. The siren will chirp twice, and the flash lights will gleam twice. The central door locking system will unlock, and the alarm system will disarm.
To arm the system silently, press the silent arm button (often represented by a speaker icon or similar) once. The flash lights will gleam once, and the central door locking system will lock, but the siren will not chirp. The system will enter arm status silently.
When the system is armed, if a car door or the hood is opened by force, or if the engine is started without disarming, the system will trigger an alarm. The siren will emit a loud 6-tone sound, flash lights will gleam, and the car engine will be cut off (immobilized). The alarm will sound for 60 seconds, then automatically stop and return to the armed state.
Before driving, if any door is not properly closed and the key is switched to the ACC/ON position, the vehicle's flash lights will continuously gleam. This serves as a warning to the driver and other road users until the door is securely closed.
While the car is moving, press the silent button once; the flash lights will gleam quickly. Then, press the lock button two times again to activate anti-hijacking status. The flash lights will gleam urgently, and the siren will chirp. After 40 seconds, the engine will be cut off. To exit anti-hijacking status, the reset button must be pressed.
If the system is disarmed but a door is not opened within 30 seconds, the system will automatically re-enter the armed status. This feature helps prevent accidental disarming.
Valet mode allows you to temporarily disable the alarm functions while the vehicle is being serviced or parked by a valet. Consult the full wiring diagram or a professional installer for specific instructions on activating and deactivating valet mode, as it typically involves a hidden switch or a specific sequence of actions.
The system supports code learning for new or replacement remote transmitters. Refer to the detailed wiring diagram for the location of the code learning button (often labeled "Code Learning" or "Learn Button") on the main unit. The general procedure involves pressing this button and then pressing a button on the new remote to pair it with the system.
| Problem | Possible Cause | Solution |
|---|---|---|
| System does not arm/disarm | Remote battery low/dead; remote out of range; faulty wiring connection. | Replace remote battery; move closer to the vehicle; check wiring connections (professional assistance recommended). |
| Siren does not sound during alarm | Siren wire disconnected; faulty siren; system in silent arm mode. | Check siren wiring; replace siren if faulty; ensure system is not in silent arm mode. |
| False alarms | Shock sensor sensitivity too high; faulty door/hood trigger. | Adjust shock sensor sensitivity (usually a dial on the sensor); inspect door/hood trigger switches and wiring. |
| Central locking not working | Incorrect central lock wiring; faulty door lock actuators. | Verify central lock wiring against vehicle's diagram; check door lock actuators. |
| Engine not cutting off during anti-hijacking | Engine immobilizer wiring incorrect or not connected. | Review and correct engine immobilizer wiring. |
For complex issues or if troubleshooting steps do not resolve the problem, it is recommended to consult a professional car alarm installer.
| Parameter | Value |
|---|---|
| Working Voltage | 9-15V |
| Output Current (Central Door Lock) | 10A |
| Output Current (Siren) | 10A |
| Output Current (Turn Light) | 10A |
| Output Current (Trunk) | 10A |
| Output Current (Power Window) | -250mA |
| Working Frequency | 433.92MHz ±400KHz |
| Standby Current (Disarm Status) | ≤12mA |
| Standby Current (Arm Status) | ≤20mA |
| Remote Controlled Distance | ≥100m |
| Siren Volume | 110-125dB |
| Working Temperature | -40℃ to +85℃ |
| Brand | BANVIE |
| Compatible Devices | Cars |
| UPC | 727523075499 |
| ASIN | B08K7HG8SV |
For warranty information and technical support, please refer to the documentation included with your product packaging or contact BANVIE customer service directly. Keep your purchase receipt as proof of purchase for warranty claims.
Manufacturer: BANVIE
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.
