1. Introduction
This manual provides essential instructions for the installation, operation, and maintenance of your DT Swiss Ratchet EXP Freehub Conversion Kit for SRAM XDR. This kit is designed to convert compatible DT Swiss hubs to accept SRAM XDR cassettes, supporting 130mm or 135mm Quick Release (QR) axle standards. Please read this manual thoroughly before proceeding with installation to ensure proper function and safety.

Image 1: DT Swiss Ratchet EXP Freehub Conversion Kit. This image displays the main components of the conversion kit, including the freehub body and associated parts.
2. Safety Information
Always prioritize safety when working with bicycle components. Improper installation or maintenance can lead to serious injury or damage to your bicycle. Observe the following safety guidelines:
- Wear appropriate personal protective equipment, such as gloves and eye protection.
- Ensure your bicycle is stable and securely supported before beginning any work.
- Use only the correct tools for each step of the installation process.
- Refer to your hub's specific service manual for detailed instructions on disassembly and reassembly, as this manual focuses on the conversion kit itself.
- If you are unsure about any step, consult a professional bicycle mechanic.
- Keep small parts away from children.
3. Package Contents
Verify that all components are present in the package before beginning installation. The DT Swiss Ratchet EXP Freehub Conversion Kit for SRAM XDR typically includes:
- 1x DT Swiss Ratchet EXP Freehub Body for SRAM XDR
- 1x End Cap (for 130mm or 135mm QR, depending on the specific kit variant)
- Other small components (e.g., springs, seals) as required for the specific hub model.
Note: The exact contents may vary slightly based on the specific product variant. Refer to the product packaging for a precise list.
4. Setup and Installation
This section outlines the general steps for installing the DT Swiss Ratchet EXP Freehub Conversion Kit. For detailed hub-specific disassembly and reassembly instructions, always consult the official DT Swiss service manual for your particular hub model.
- Prepare the Wheel: Remove the rear wheel from the bicycle. Remove the cassette from the existing freehub body.
- Remove Existing Freehub: Carefully remove the existing freehub body and end cap from the hub axle. This usually involves pulling the end cap off and then sliding the freehub body off the axle. Pay attention to the orientation and any small parts (e.g., springs, pawls if not Ratchet EXP).
- Clean and Inspect: Clean the hub shell and axle thoroughly. Inspect the Ratchet EXP system components (ratchet rings, springs) for wear or damage. Replace any worn parts as necessary.
- Lubricate: Apply a thin layer of DT Swiss special grease (or equivalent compatible grease) to the ratchet rings and springs within the hub shell and on the new freehub body. Ensure proper lubrication for smooth operation and longevity.
- Install New Freehub: Slide the new DT Swiss Ratchet EXP Freehub Body for SRAM XDR onto the hub axle. Ensure the ratchet rings engage correctly.
- Install End Cap: Install the appropriate end cap for 130mm or 135mm QR onto the new freehub body. It should snap securely into place.
- Install Cassette: Install your SRAM XDR cassette onto the new freehub body, ensuring it is properly tightened to the manufacturer's specifications.
- Reinstall Wheel: Reinstall the wheel onto your bicycle, ensuring the quick release skewer is properly secured.
- Function Check: Spin the wheel and check the drivetrain for smooth operation and proper shifting.
For visual guidance, refer to official DT Swiss service videos or consult a qualified mechanic.
5. Operating Instructions
Once installed, the DT Swiss Ratchet EXP Freehub Conversion Kit functions as an integral part of your bicycle's drivetrain, allowing the use of SRAM XDR cassettes. Its operation is passive, facilitating power transfer from the pedals to the rear wheel and allowing the wheel to freewheel when not pedaling.
- Engagement: The Ratchet EXP system provides quick and reliable engagement when you begin pedaling, transferring power efficiently.
- Freewheeling: When you stop pedaling, the freehub allows the wheel to rotate independently, producing the characteristic "buzz" sound of the ratchet system.
- Compatibility: Ensure your chain, derailleur, and shifters are compatible with your SRAM XDR cassette for optimal performance.
6. Maintenance
Regular maintenance of your DT Swiss Ratchet EXP freehub ensures its longevity and optimal performance. The Ratchet EXP system is known for its durability and ease of service.
- Cleaning: Periodically remove the freehub body and clean the ratchet rings and hub shell interior. Remove any accumulated dirt or old grease.
- Lubrication: Re-lubricate the ratchet rings and springs with DT Swiss special grease (or a compatible, non-migrating, low-viscosity grease specifically designed for freehub mechanisms). Avoid using thick, heavy greases as they can impede ratchet engagement, especially in cold weather.
- Inspection: Inspect the ratchet rings, springs, and freehub body for any signs of wear, pitting, or damage. Replace components as needed.
- Frequency: Maintenance frequency depends on riding conditions. For regular use in dry conditions, annual inspection and lubrication are often sufficient. For wet, muddy, or extreme conditions, more frequent checks are recommended.
Always refer to the official DT Swiss service manual for your specific hub model for detailed maintenance procedures and recommended lubricants.
7. Troubleshooting
This section addresses common issues you might encounter with your freehub conversion kit.
| Problem | Possible Cause | Solution |
|---|---|---|
| Freehub not engaging / slipping |
|
|
| Excessive noise from freehub |
|
|
| Cassette wobble |
|
|
If you are unable to resolve an issue, contact DT Swiss customer support or a certified bicycle mechanic.
8. Specifications
| Feature | Detail |
|---|---|
| Product Name | DT Swiss Ratchet EXP Freehub Conversion Kit |
| Model Number | HWYABL00S5382S |
| Compatibility | SRAM XDR cassettes |
| Axle Standard | 130mm or 135mm Quick Release (QR) |
| Freehub System | Ratchet EXP |
| Material | Plastic (referring to packaging/some components, actual freehub is metal) |
| Item Weight | 100 Grams |
| Manufacturer | DT Swiss |
9. Warranty Information
DT Swiss products are covered by a Limited Warranty. This warranty typically covers defects in materials and workmanship under normal use. The duration and specific terms of the warranty may vary by region and product. Please retain your proof of purchase.
For complete and up-to-date warranty details, please visit the official DT Swiss website or contact their customer support directly. The warranty does not cover damage resulting from improper installation, misuse, neglect, accidents, or normal wear and tear.
10. Customer Support
If you have any questions, require technical assistance, or need to report an issue with your DT Swiss Ratchet EXP Freehub Conversion Kit, please contact DT Swiss customer support.
Official Website: www.dtswiss.com
You can typically find contact information, FAQs, and service manuals on their official website.