VINABTY NB694UH Remote Control Instruction Manual

1. Introduction

This manual provides comprehensive instructions for the VINABTY NB694UH replacement remote control. It is designed to operate specific Sanyo, Funai, and Magnavox DVD VCR Combo Players, including models such as FWDV225F, NB693, NB693UH, NB695, NB695UH, MDV260V, and MDV260V/F7. Please read this manual carefully before use to ensure proper operation and to maximize the functionality of your remote control.

2. Product Overview

The VINABTY NB694UH is a dedicated replacement remote control, designed to replicate the functions of the original remote for compatible DVD VCR Combo Players. It features a standard layout for easy navigation and control of both DVD and VCR functions.

Image 2.1: Front view of the VINABTY NB694UH remote control, showing all buttons and their labels for various functions including Power, Play, Stop, VCR, DVD, and navigation controls.

3. Setup

3.1 Battery Installation

The remote control requires two (2) AAA alkaline batteries for operation. Please follow these steps to install the batteries:

1. Locate the battery compartment on the back of the remote control.
2. Slide the battery compartment cover downwards to open it.
3. Insert two new AAA alkaline batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment. The correct polarity is typically + to - and - to +.
4. Slide the battery compartment cover back into place until it clicks securely.

Important: Do not use rechargeable batteries or non-alkaline AAA batteries, as these may not provide sufficient power or may cause damage to the remote control.

Image 3.1: Rear view of the VINABTY NB694UH remote control with the battery compartment open, showing the correct orientation for AAA battery installation.

3.2 No Programming Required

This replacement remote control is pre-programmed and does not require any additional setup or programming. Once batteries are correctly installed, it is ready for immediate use with compatible Sanyo, Funai, and Magnavox DVD VCR Combo Players.

4. Operating Instructions

To operate your DVD VCR Combo Player with the VINABTY NB694UH remote control, point the remote directly towards the infrared (IR) sensor on your player. Ensure there are no obstructions between the remote and the player.

4.1 Key Functions

• POWER: Turns the DVD VCR Combo Player on or off.
• VCR / DVD: Switches between VCR and DVD modes.
• PLAY (►): Starts playback of a DVD or VCR tape.
• STOP (■): Stops playback.
• PAUSE (⏸): Pauses playback.
• REV (⏪): Rewinds VCR tape or fast reverses DVD.
• FWD (⏩): Fast forwards VCR tape or fast forwards DVD.
• REC (●): Initiates recording on VCR (if supported by the player).
• SKIP (⏮ / ⏭): Skips tracks/chapters on DVD or skips forward/backward on VCR.
• OPEN/CLOSE: Opens or closes the DVD tray.
• AUDIO: Selects audio tracks or modes.
• SUBTITLE: Toggles or selects subtitle options.
• DISC MENU: Accesses the DVD disc menu.
• TITLE: Accesses the DVD title menu.
• ZOOM: Adjusts the zoom level of the picture.
• ANGLE: Changes the camera angle on compatible DVDs.
• A-B: Repeats a specific section between two points (A and B).
• REPEAT: Repeats current track, chapter, or disc.
• INPUT: Selects input source.
• DISPLAY: Shows on-screen display information.
• SEARCH: Initiates search functions.
• MODE: Changes playback modes.
• SETUP: Accesses the player's setup menu.
• NAVIGATION BUTTONS (▲, ▼, ◄, ►): Used to navigate menus.
• ENTER: Confirms selections in menus.
• CLEAR: Clears entries or selections.
• RETURN: Returns to the previous menu or screen.
• SPEED: Adjusts playback speed.
• TIMER SET: Sets timer recording for VCR.
• TRACKING: Adjusts VCR tracking for optimal picture quality.

5. Troubleshooting

If your VINABTY NB694UH remote control is not functioning as expected, please refer to the following troubleshooting steps:

5.1 No Response or Remote Does Not Work

1. Battery Check: Ensure that two new AAA alkaline batteries are correctly installed with the proper positive (+) and negative (-) polarity. Incorrect installation or depleted batteries are common causes of remote control malfunction.
2. Compatibility Verification: Confirm that your DVD VCR Combo Player's model number is listed as compatible with the NB694UH remote control. This remote is specifically designed for Sanyo FWDV225F, Funai, and Magnavox models NB693, NB693UH, NB695, NB695UH, MDV260V, and MDV260V/F7.
3. Obstruction Check: Ensure there are no physical obstructions between the remote control and the infrared (IR) sensor on your DVD VCR Combo Player. The effective control range is approximately 10 meters (30 feet) within a 30-degree angle.

5.2 Advanced Troubleshooting Steps

If the remote still does not work after performing the initial checks, try these advanced steps:

1. Reset Remote:
   • Remove the batteries from the remote control.
   • Press every button on the remote control for at least 3-5 seconds each. This helps to drain any residual power and check for stuck buttons.
2. Clean IR Sensor: Check if the IR sensor area on your DVD VCR Combo Player is clean. Dust or debris can sometimes interfere with the infrared signal reception.
3. Player Reset: Unplug the power supply of your DVD VCR Combo Player from the electrical outlet, wait for about 30 seconds, and then plug it back in to restart the player. After the player has fully powered on, try using the remote control again.
4. Reinsert New Batteries: Insert two new AAA alkaline batteries into the remote, ensuring correct polarity (+ to -; - to +). Double-check that you are not using rechargeable or non-alkaline batteries.

6. Specifications

7. Warranty and Support

For warranty information or technical support regarding your VINABTY NB694UH remote control, please refer to the purchase documentation or contact the seller directly. Keep your proof of purchase for any warranty claims.

For issues related to your DVD VCR Combo Player, please consult the original manufacturer's manual or support channels for that specific device.