Yaheetech 7.5ft Premium Snow Flocked Hinged Artificial Christmas Spruce Tree Instruction Manual

Introduction

Thank you for choosing the Yaheetech 7.5ft Premium Snow Flocked Hinged Artificial Christmas Spruce Tree. This manual provides detailed instructions for the safe assembly, operation, and maintenance of your new artificial Christmas tree. Please read all instructions carefully before assembly and retain this manual for future reference.

Image: A fully assembled Yaheetech 7.5ft Premium Snow Flocked Artificial Christmas Spruce Tree, showcasing its full, snow-dusted appearance.

Safety Information

• Ensure all parts are present and undamaged before assembly.
• Assemble the tree on a flat, stable surface to prevent tipping.
• Keep the tree away from open flames, heat sources, and direct sunlight to prevent damage and fire hazards.
• This product is for indoor and outdoor use; however, protect it from extreme weather conditions if used outdoors.
• Keep small children and pets away from the tree during assembly and ensure all small parts are out of reach.
• The tree branches are bendable; exercise caution when adjusting to avoid injury.

Package Contents

Verify that all components listed below are included in your package:

• Artificial Christmas Tree sections (typically 3 sections for 7.5ft models)
• Metal Stand
• Protective caps for stand feet

Setup and Assembly

Follow these steps to assemble your Yaheetech Artificial Christmas Tree:

Step 1: Prepare the Stand

Locate the foldable metal stand. Open it to form an 'X' shape. Insert the protective caps onto the ends of the stand's legs to prevent floor scratches. Ensure the stand is stable.

Image: A close-up showing the foldable metal stand and the "Simple Set-Up" and "Flocked Snow" features of the tree.

Step 2: Assemble the Tree Sections

1. Insert the Bottom Trunk: Take the lowest numbered tree section (e.g., "Part 3" or "C") and remove its protective cover. Insert the bottom pole of this section into the center hole of the metal stand. Tighten the screws on the stand to secure the trunk firmly.
2. Insert Middle Trunks: Proceed with the next tree section (e.g., "Part 2" or "B"). Align its pole with the top of the previously assembled section and insert it.
3. Insert the Top Trunk: Finally, take the highest numbered tree section (e.g., "Part 1" or "A") and insert it into the top of the middle section.

Image: A detailed view of the hinged branch system, illustrating how branches automatically fan out when sections are connected.

The tree features a hinged system where branches are pre-attached to the trunk. They will automatically fall into place as you assemble each section.

Step 3: Fluff and Shape the Branches

For a full and realistic appearance, it is essential to properly fluff and shape each branch. This process involves separating individual tips and bending them outwards and upwards. Start from the bottom section and work your way up, ensuring even distribution of branches.

Image: A visual guide demonstrating the four steps to fluff and shape the tree branches, transforming them from a compact state to a full, natural look. An example of a tree "Before" and "After" fluffing is also shown.

For a 7.5ft tree, this process typically takes 1.5 to 2 hours to achieve optimal fullness.

Image: A detailed close-up of the snow-flocked PVC branches, highlighting the texture and snow-dusted effect.

Tip: To minimize debris from the flocking during initial setup, consider laying a protective sheet or paper under the tree area.

Image: A suggestion to place brown paper under the tree during installation to keep the floor clean from any flocking or branch chips.

Operating (Decoration and Placement)

Once assembled and fluffed, your Yaheetech Christmas tree is ready for decoration and placement.

• Placement: Choose a prominent location in your home or office. Ensure there is enough space around the tree for safe movement and decoration.
• Decorating: The flexible tips allow for easy hanging of ornaments and lights. Distribute decorations evenly for a balanced appearance.
• Lighting: This tree is not pre-lit, allowing you to customize your lighting choice. Use appropriate indoor/outdoor lights as per their manufacturer's instructions.

Image: A beautifully decorated Yaheetech snow flocked Christmas tree, adorned with colorful ornaments and lights, placed in a festive living room.

Maintenance

• Cleaning: To clean the tree, gently dust the branches with a soft cloth or use a vacuum cleaner on a low setting with a brush attachment. Do not use harsh chemicals or abrasive cleaners.
• Storage: Before storing, remove all decorations and lights. Disassemble the tree in reverse order of assembly. Compress the branches to their original compact state. Store all parts in their original packaging or a suitable storage bag in a cool, dry place away from direct sunlight and extreme temperatures.
• Flocking: Some minor shedding of the snow flocking is normal during initial setup and handling. This will decrease over time.

Troubleshooting

• Tree is not full: Ensure all branches have been thoroughly fluffed and shaped. This is a crucial step for achieving the tree's intended fullness. Refer to the "Fluff and Shape the Branches" section.
• Tree is wobbly: Check that the metal stand is fully extended and placed on a level surface. Ensure the screws on the stand are tightened securely around the bottom tree section.
• Excessive flocking shedding: While some shedding is normal, excessive shedding might occur if the tree is handled roughly. Handle branches gently during assembly and decoration.

Specifications

Image: A visual representation of the tree's height (90 inches or 7.5 feet) and base diameter (55 inches).

Warranty and Support

For warranty information or customer support, please refer to the product packaging or contact Yaheetech directly through their official website or the retailer where the product was purchased. Keep your purchase receipt as proof of purchase.