Introduction
Thank you for choosing the TORRAS Electric Lint Remover. This device is designed to efficiently remove lint and pills from various fabrics, restoring your garments and upholstery to a like-new condition. Please read this manual carefully before use to ensure safe and optimal performance.
Safety Precautions
- Keep the device out of reach of children.
- Do not use the device on wet fabrics.
- Ensure the protective cover is securely in place before operation.
- Do not press the device too hard against the fabric to avoid damage.
- Avoid touching the blades directly.
- Unplug the device before cleaning or when not in use for extended periods.
- If the device enters safety mode (indicated by three lamps flashing), clean the lint collector and reattach the front cover securely. If the issue persists, contact customer support.
Package Contents
- TORRAS Electric Lint Remover
- Replacement Blades
- Cleaning Brush
- USB Charging Cable
- User Manual
Product Overview
- Protective Cover: 0.38mm aerospace-grade stainless steel cover with a 9° floating design to protect fabrics.
- 6-Blade System: High-precision stainless steel blades for efficient lint removal.
- Motor: Powerful 11000 RPM motor for quick and effective operation.
- Lint Collector: Transparent, detachable container for collected lint.
- Power Button/Mode Selector: Controls power and switches between 3 speed modes.
- Charging Port: USB-C port for convenient charging.
- Fluffy Guard: An accessory designed to protect delicate fabrics.
- AI Protection Chip: Monitors operation 233 times per second to prevent fabric damage.
Setup
1. Charging the Device
Before first use, fully charge the lint remover. Connect the provided USB cable to the device's charging port and a suitable USB power adapter (not included). The indicator lights will show the charging status. A full charge provides up to 180 minutes of continuous use.
2. Attaching the Fluffy Guard
For delicate fabrics, attach the fluffy guard to the protective cover. This accessory helps maintain an optimal distance between the blades and the fabric, preventing damage.
Operating Instructions
1. Preparing the Fabric
Lay the garment or fabric flat on a hard, smooth surface. Ensure there are no wrinkles or folds that could be caught by the blades.
2. Powering On and Selecting Mode
Press the power button to turn on the device. Press the button repeatedly to cycle through the three speed modes:
- Mode 1 (Low Speed): Ideal for delicate fabrics like silk or thin knits.
- Mode 2 (Medium Speed): Suitable for everyday fabrics like cotton or synthetic blends.
- Mode 3 (High Speed): Best for thick fabrics such as wool coats, sweaters, or upholstery.
3. Removing Lint
Gently glide the lint remover over the fabric surface. Do not apply excessive pressure. The device is designed to lift and cut lint effectively without pulling or damaging the fabric. Work in small sections, moving the device in circular motions or straight strokes.
Maintenance
1. Emptying the Lint Collector
Regularly check and empty the lint collector. The collector is magnetically attached for easy removal. Simply pull it off, discard the collected lint, and reattach it securely.
2. Cleaning the Blades and Protective Cover
After emptying the lint collector, use the provided cleaning brush to remove any remaining lint or debris from the blades and the inside of the protective cover. Ensure the device is turned off before cleaning.
3. Replacing Blades
When the blades become dull or damaged, they can be replaced. Refer to the replacement blade instructions for detailed steps. Ensure the device is off and unplugged before attempting to replace blades.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Device does not turn on or charge. | Low battery; Safety mode activated; Loose front cover. | Charge the device fully. Ensure the front cover is securely attached. Clean the lint collector and reattach the cover to deactivate safety mode. |
| Poor lint removal performance. | Lint collector is full; Blades are dull or dirty; Incorrect speed mode. | Empty the lint collector. Clean the blades and cover. Select a higher speed mode for thicker fabrics. Consider replacing blades if dull. |
| Device stops during operation. | Safety mode activated (e.g., cover loose, collector full). | Check if the front cover is loose or the lint collector is full. Secure the cover and empty the collector. |
Specifications
| Feature | Detail |
|---|---|
| Brand | TORRAS |
| Model Number | B08HCYQQZV |
| Material | High-quality Stainless Steel |
| Color | Red-Purple (Main Unit) |
| Product Dimensions (D x W x H) | 7.3 x 6.5 x 17.8 cm |
| Handle Material | Stainless Steel |
| Unit Count | 1 |
| Operation Mode | Automatic |
| Motor Speed | 11000 RPM |
| Blades | 6-blade system |
| Battery Capacity | 2000mAh |
| Continuous Use Time | Up to 180 minutes (Low Speed) |
| Charging | USB-C, 2-way power (cordless or while charging) |
Warranty & Support
Manufacturer Warranty
This product comes with a 365-day long-term quality warranty. If the product breaks, fails to charge, or does not operate under normal use within the warranty period, a one-time new product replacement service will be provided unconditionally.
Contact Support
For warranty claims or any inquiries, please contact TORRAS customer support. You can typically find the contact option by navigating to the seller's page on the purchase platform (e.g., Amazon) and selecting "Ask a question" under the seller's name.
Important Note on Videos
No official product video URLs were provided in the product data. Therefore, no videos could be embedded in this manual.