HONWELL H600

Download PDF
Contents

HONWELL Wireless LED Picture Light H600 Instruction Manual

Model: H600 | Brand: HONWELL

1. Introduction

Thank you for choosing the HONWELL Wireless LED Picture Light H600. This manual provides detailed instructions for the safe and efficient use of your new picture light. Please read it thoroughly before installation and operation, and retain it for future reference.

Package Contents:

  • 1 x HONWELL Wireless LED Picture Light
  • 1 x Remote Control (CR2025 button cell battery included)
  • 1 x Micro-USB Charging Cable
  • 3 x Screws
  • 1 x User Manual (this document)

2. Safety Information

  • Do not attempt to disassemble or modify the light.
  • Keep the device away from water and high humidity.
  • Ensure the charging cable is not damaged before use.
  • Do not insert screws directly through the artwork or picture frame.
  • Verify that the mounting bracket is securely fastened to prevent the light from falling.
  • The remote control contains a button cell battery. Keep it out of reach of children.

3. Setup and Installation

The HONWELL Picture Light offers flexible installation options to suit various needs.

Installation Options:

  1. Clip-on Installation:

    This method is suitable for picture frames with a thickness of 25-35mm. Simply attach the clip-on bracket to the top edge of your frame. Ensure it is firmly secured.

  2. Screw-in Installation:

    For a more permanent fixture or for mounting directly to a wall above artwork, use the provided screws and anchors. Attach the mounting plate to the desired surface, then secure the light to the plate. Ensure the mounting surface is appropriate for screws.

Diagram showing two installation methods: clip-on for picture frames and screw-in for wall mounting. The clip-on method is suitable for frames 25-35mm thick. The screw-in method shows screws and anchors for wall installation.

Figure 1: Installation Options for the HONWELL Picture Light.

Initial Charging:

Before first use, fully charge the picture light. The light is powered by a high-capacity 3.7V 2*2200mAh Li-ion battery. Connect the micro-USB charging cable to the light and to any standard USB charging port (e.g., power bank, laptop, USB wall charger). A full charge takes approximately 5-6 hours. The LED indicator will automatically turn off once charging is complete.

Diagram showing the light head being twisted off for charging. A micro-USB cable is shown connecting to the light, with illustrations of a USB charger, laptop, and computer as charging sources.

Figure 2: Charging the HONWELL Picture Light. The light head can be detached for convenient charging.

4. Operating Instructions

The HONWELL Picture Light can be operated via its integrated button or the included remote control.

Adjusting Light Direction:

The light features an adjustable design for optimal illumination:

  • The light head can be rotated 180° to direct light precisely.
  • The flexible gooseneck allows for a 360° adjustment, enabling you to position the light exactly where needed.

Manual Operation (On-Light Button):

Press the button located on the light head to cycle through the lighting modes:

  1. Press once for 4300K Natural White light.
  2. Press again for 3000K Warm White light.
  3. Press a third time for 8000K Cool White light.
  4. Press a fourth time to turn the light OFF.
Image showing three different light color temperatures (8000K, 4300K, 3000K) illuminating artwork. Below, a hand is pressing the button on the light head, and a remote control is shown with its functions listed.

Figure 3: Light Modes and Manual Control.

Remote Control Operation:

The remote control allows for convenient operation from up to 20 feet away. A single remote can control up to 10 HONWELL picture lights.

  • ON/OFF: Power button to turn the light on or off.
  • Dimmer:
    • 50% / 100%: Directly set brightness to 50% or 100%.
    • + / -: Adjust brightness incrementally (increase/decrease).
  • Color Temperature:
    • Warm White Button: Activates 3000K Warm White light.
    • Cool White Button: Activates 8000K Cool White light.
    • Natural White Button: Activates 4300K Natural White light (often represented by a combined warm/cool icon).
  • Timer Functions: Set the light to automatically turn off after a specified duration.
    • 15 min: Auto-off after 15 minutes.
    • 30 min: Auto-off after 30 minutes.
    • 60 min: Auto-off after 60 minutes.
    • 120 min: Auto-off after 120 minutes.
Image showing three artworks illuminated by the picture light. Below, a detailed diagram of the remote control with labels for ON/OFF, brightness up/down, 50%/100% brightness, 15/30/60/120 minute timers, warm white button, and cool white button.

Figure 4: Remote Control Functions.

5. Maintenance

Charging the Battery:

When the light's brightness diminishes, it indicates a low battery. Recharge the light using the provided micro-USB cable as described in the "Initial Charging" section. A full charge provides illumination for up to 24 hours, though actual runtime may vary based on brightness settings and color temperature used.

Cleaning:

Wipe the light gently with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or electronic components.

Remote Control Battery Replacement:

The remote control uses a CR2025 button cell battery. If the remote's range or responsiveness decreases, replace the battery. Refer to the diagram below for battery replacement steps.

Diagram showing how to open the remote control to replace the CR2025 battery. Steps include sliding the back cover, removing the old battery, inserting a new one, and closing the cover.

Figure 5: Remote Control Battery Replacement (refer to the bottom right section of the image).

6. Troubleshooting

  • Light does not turn on:
    • Ensure the battery is charged. Connect to a power source and allow it to charge for at least 30 minutes.
    • Check if the remote control battery is functional. Replace if necessary.
    • Try operating the light using the manual button on the light head.
  • Remote control not working:
    • Ensure there are no obstructions between the remote and the light.
    • Verify the remote control battery is correctly inserted and has sufficient power. Replace if needed.
    • Ensure you are within the 20-foot operating range.
  • Light flickers or is dim:
    • The battery level is likely low. Recharge the light fully.

7. Specifications

Feature Detail
Model Number H600
Light Source 28 SMD LEDs
Luminous Flux 200 Lumens (±10%)
Wattage 1.5 Watts
Color Temperatures 3000K (Warm White), 4300K (Natural White), 8000K (Cool White)
Battery 3.7V 4400mAh (2*2200mAh) Li-ion
Charging Time 5-6 hours (full charge)
Run Time Up to 24 hours (depending on brightness/mode)
Control Method Remote Control, Manual Button
Remote Range Up to 20 feet
Dimensions (Light Head) 8.4 inches / 21.4 cm (length)
Gooseneck Length 7.1 inches / 18 cm
Product Dimensions (L x W x H) 6 x 22 x 39 cm
Weight 550 grams
Material Metal, Plastic
Installation Type Wall Mount, Clip-on
Diagram showing the dimensions of the picture light and its components, including the gooseneck and mounting bracket. Key specifications like lumens, wattage, color temperature, battery capacity, run time, and number of LEDs are also displayed.

Figure 6: Product Dimensions and Key Specifications.

8. Warranty and Support

Warranty Information:

Specific warranty details for the HONWELL Wireless LED Picture Light H600 are not provided in this manual. Please refer to the product packaging or the retailer's website for warranty terms and conditions.

Customer Support:

For technical assistance, troubleshooting beyond this manual, or inquiries regarding your HONWELL product, please contact the manufacturer or your point of purchase. Contact information can typically be found on the product packaging or the official HONWELL website.

© 2023 HONWELL. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.