Weber 67279 Crossover Burner Tube Instruction Manual

Introduction

This manual provides instructions for the installation and maintenance of the Weber 67279 Crossover Burner Tube. This genuine Weber replacement part is designed for Weber Spirit and Spirit II 310 Series gas grills manufactured in 2013 and newer. The crossover tube plays a crucial role in igniting all main burners efficiently by transferring flame from one lit burner to the adjacent unlit burners.

Image: The Weber 67279 Crossover Burner Tube, a stainless steel component designed for flame transfer between grill burners.

Setup and Installation

Before beginning installation, ensure your grill is completely cool and the gas supply is turned off and disconnected. It is recommended to wear protective gloves during this process.

1. Safety First: Turn off the gas supply at the propane tank or natural gas line. Disconnect the gas tank or ensure the gas line valve is closed.
2. Access Burners: Open the grill lid and remove the cooking grates and flavorizer bars to expose the main burner tubes.
3. Remove Old Crossover Tube: Locate the existing crossover burner tube, which connects the main burner tubes. It is typically held in place by a screw or simply rests in position. Carefully remove any fasteners and then lift out the old crossover tube.
4. Clean Grill Interior: While the components are removed, take the opportunity to clean any debris, grease, or rust from the burner box and surrounding areas.
5. Install New Crossover Tube: Position the new Weber 67279 Crossover Burner Tube into place, ensuring it properly aligns with the openings on the main burner tubes. If applicable, secure it with the original fasteners.
6. Reassemble Grill: Replace the flavorizer bars and cooking grates.
7. Test for Leaks: Reconnect the gas supply. Before lighting, perform a leak test by applying a soapy water solution to all gas connections. If bubbles appear, tighten the connection and retest. Do not proceed if leaks are detected.
8. Test Ignition: With the lid open, turn on the gas supply and attempt to light the grill according to your grill's operating instructions. Observe that all main burners ignite properly via the crossover tube.

For detailed visual guidance, refer to your grill's original instruction manual or official Weber support resources.

Operating Principles

The Weber 67279 Crossover Burner Tube is an integral part of your grill's ignition system. When the first main burner is ignited, the flame travels through the small openings in the crossover tube, igniting the adjacent main burners. This ensures a quick and even ignition across the entire cooking surface, provided the main burners are clean and functioning correctly.

Maintenance

Regular maintenance of your crossover burner tube helps ensure optimal grill performance and longevity.

• Cleaning: Periodically inspect the crossover tube for grease buildup or blockages. With the gas supply off and the grill cool, gently clean the tube using a soft brush or a grill brush with soft bristles. Avoid abrasive cleaners that could damage the stainless steel.
• Inspection: Check for any signs of corrosion, cracks, or damage to the tube. While stainless steel is durable, extreme heat and environmental factors can cause wear over time. If significant damage is observed, replacement may be necessary.
• Burner Port Alignment: Ensure the crossover tube remains properly aligned with the burner ports for efficient flame transfer.

Troubleshooting

If you experience issues with your grill's ignition after installing or while using the crossover tube, consider the following:

• Burners Not Lighting Evenly:
  • Check if the crossover tube is properly seated and aligned with all main burner ports.
  • Inspect the crossover tube for any blockages (e.g., spider webs, debris) that might impede flame transfer.
  • Ensure the main burner tubes themselves are clean and their ports are not clogged.
• No Flame Transfer:
  • Verify that the gas supply is fully open and there are no leaks.
  • Confirm that the igniter is sparking correctly at the first burner.
  • Ensure the crossover tube is not damaged or severely corroded, which could prevent flame passage.

If troubleshooting steps do not resolve the issue, consult a qualified technician or contact Weber customer support.

Specifications

Warranty and Support

For specific warranty information regarding the Weber 67279 Crossover Burner Tube, please refer to the official Weber website or contact Weber customer service directly. Warranty terms and conditions may vary.

For additional support, product registration, or to find authorized service centers, visit the official Weber website: www.weber.com.