1. Introduction
The Fender Acoustic Junior GO amplifier is designed to provide full, natural sound for acoustic-electric guitars and vocals. This portable system features two independent channels, each equipped with studio-quality effects. Key functionalities include Bluetooth wireless audio streaming and an integrated 90-second looper, making it suitable for various performance settings. Its rechargeable battery allows for extended use without a power outlet.
2. Setup
2.1. Unpacking
Carefully remove the amplifier from its packaging. Retain all packaging materials for future transport or storage. Inspect the amplifier for any signs of damage. If damage is present, contact your retailer immediately.
2.2. Powering On and Charging
The Acoustic Junior GO amplifier is equipped with a rechargeable lithium-ion battery. For initial use, it is recommended to fully charge the battery. Connect the provided power adapter to the amplifier's power input and then to a suitable electrical outlet. The charging indicator will illuminate. A full charge provides approximately 5 hours of playing time at full volume or 12 hours at moderate volume. The amplifier can also be operated while connected to AC power.
2.3. Connecting Instruments and Microphones
The amplifier features two independent channels:
- Channel 1: Designed for acoustic-electric guitars. Connect your instrument using a standard 1/4-inch instrument cable.
- Channel 2: Designed for microphones. Connect your microphone using an XLR cable. This channel also supports 1/4-inch instrument inputs.
Ensure all connections are secure before powering on the amplifier.
3. Operating Instructions
3.1. Channel Controls
Each channel features independent controls for volume, equalization (bass, middle, treble), and effects. Adjust these controls to achieve your desired sound. Experiment with different settings to find the optimal tone for your instrument or voice.
3.2. Bluetooth Pairing
To stream audio wirelessly from a phone or tablet:
- Activate Bluetooth on your mobile device.
- Press the Bluetooth pairing button on the amplifier. The indicator light will flash.
- Select 'Fender Acoustic Junior GO' from the list of available devices on your mobile device.
- Once paired, the indicator light will remain solid, and you can stream audio through the amplifier.
3.3. Looper Function
The onboard 90-second looper allows for recording and layering audio. The looper controls include:
- Record/Dub: Press once to start recording. Press again to overdub.
- Play/Stop: Press once to play the loop. Press again to stop.
- Undo: Reverts the last overdub.
Refer to the detailed looper section in the full manual for advanced techniques.
3.4. Tilt-Back Kickstand
The amplifier features an integral tilt-back kickstand. This allows you to angle the amplifier upwards, directing the sound more effectively towards the performer or audience, especially in smaller venues or when placed on the floor.
4. Maintenance
4.1. Cleaning
To clean the amplifier, use a soft, dry cloth. For stubborn dirt, a slightly damp cloth may be used, followed by a dry cloth. Avoid using abrasive cleaners, solvents, or waxes, as these can damage the finish and components.
4.2. Storage
Store the amplifier in a cool, dry place away from direct sunlight and extreme temperatures. If storing for an extended period, ensure the battery is partially charged (around 50%) to prolong its lifespan.
4.3. Battery Care
To maximize the life of the lithium-ion battery:
- Avoid fully discharging the battery regularly.
- Do not expose the amplifier to extreme heat or cold.
- If the amplifier will not be used for several months, charge it to approximately 50% every 3-6 months.
5. Troubleshooting
This section addresses common issues you might encounter with your Fender Acoustic Junior GO amplifier.
| Problem | Possible Cause | Solution |
|---|---|---|
| No sound output | Volume controls are low; cables are not connected properly; instrument/microphone issue; amplifier not powered on. | Check all volume knobs (master, channel, instrument/mic). Ensure cables are securely connected. Verify instrument/microphone functionality. Confirm amplifier is powered on and charged. |
| Bluetooth not pairing | Bluetooth not activated on device; amplifier not in pairing mode; device too far. | Ensure Bluetooth is enabled on your device. Press the amplifier's Bluetooth button to enter pairing mode. Move your device closer to the amplifier. |
| Looper not recording/playing | Incorrect button sequence; looper memory full (unlikely for 90s). | Review the looper operating instructions. Ensure you are pressing the correct buttons for record, dub, play, and stop. |
| Distorted sound | Input signal too high; volume too high; faulty cable. | Reduce the input gain or volume on the instrument/microphone channel. Lower the master volume. Try a different cable. |
6. Specifications
| Feature | Detail |
|---|---|
| Model Name | Acoustic Junior GO |
| Model Number | 2314400000 |
| Brand | Fender |
| Output Wattage | 100 Watts |
| Product Dimensions | 16 x 20 x 16 inches (Height x Width x Depth) |
| Item Weight | 20.6 pounds |
| Battery Type | Rechargeable Lithium-Ion |
| Battery Life | Up to 5 hours (full volume), 12 hours (moderate volume) |
| Connectivity | Bluetooth, 1/4-inch instrument input, XLR microphone input |
| Looper | 90-second with Record/Dub, Play/Stop, Undo |
| Voltage | Universal voltage for global use |
7. Warranty and Support
Fender products are designed for reliability and performance. For information regarding warranty coverage, product registration, or technical support, please visit the official Fender website or contact Fender customer service. Keep your proof of purchase for warranty claims.
Online Support: www.fender.com/support
