1. Introduction
Thank you for choosing the Eapmic Smart Electric Bidet Seat. This manual provides essential information for the safe installation, operation, and maintenance of your new bidet seat. Please read this manual thoroughly before installation and use, and retain it for future reference.
2. Safety Information
Please observe the following safety precautions to prevent injury or damage to the product.
- Ensure the power outlet is properly grounded and matches the specified voltage (AC110V).
- Do not immerse the bidet seat or power cord in water or other liquids.
- Unplug the unit before cleaning or performing any maintenance.
- Do not attempt to repair the unit yourself. Contact qualified service personnel for assistance.
- Keep children away from the bidet seat's controls and ensure they are supervised if using the product.
- Avoid using abrasive cleaners or harsh chemicals on the bidet seat.
- This product is designed for indoor use only.
3. Package Contents
Verify that all components are present before beginning installation:
- Eapmic Smart Electric Bidet Seat (x1)
- Water Inlet Tube (approx. 31.5 inches length, 0.7 inches inner diameter) (x1)
- 1/2" 3-Way Connector (x1)
- Installation Hardware (bolts, washers, mounting plates)
Image: All components of the Eapmic Smart Electric Bidet Seat package, including the seat, water inlet tube, 3-way connector, and mounting hardware.
4. Features
The Eapmic Smart Electric Bidet Seat offers a range of features for enhanced hygiene and comfort:
- Oscillating Wash: Provides a broader and more thorough cleaning experience.
- Automatic Deodorization: Helps maintain a fresh bathroom environment.
- IPX4 Water Proofing: Ensures protection against splashing water.
- Water-Filtering: For a cleaner wash.
- Self-Cleaning Twin Nozzles: Nozzles clean themselves before and after each use.
- Adjustable Water Temperature: Customize water temperature for comfort (4-step adjustment: OFF, 33℃, 36℃, 40℃).
- Adjustable Washing Position: Fine-tune the nozzle position for optimal cleaning.
- Adjustable Water Spraying Intensity: Control the strength of the water stream.
- Adjustable Air Dryer Temperature: Warm air dryer with adjustable temperature (32℃-48℃).
- Massage Mode: Provides a pulsating wash for a soothing experience.
- Built-in Automatic Body Sensor: Activates functions only when seated.
- Heated Anti-Bacterial Seat: Provides consistent warmth and hygiene. Adjustable seat temperature.
- Slow-Closing Lid: Prevents slamming and reduces noise.
- Multi-Safeguards: Includes float switch, temperature sensor, and temperature fuse for safety.
Image: The Eapmic Smart Electric Bidet Seat with its control panel, shown installed on a toilet in a contemporary bathroom setting.
5. Specifications
| Parameter | Value |
|---|---|
| Model | B08FX355Y1 |
| Voltage | AC110V |
| Water Pressure Range | 0.08 to 0.75 Mpa (0.8-7.5kgf/cm²) |
| Water Flow Rate (Wash) | Max 0.8 L/min |
| Water Flow Rate (Bidet) | Max 0.95 L/min |
| Water Temperature Control | 4-step (OFF, 33℃, 36℃, 40℃) |
| Washing Power | 1300W |
| Tank Capacity | 0.55L |
| Warm Air Power | 250W |
| Air Dryer Temperature Control | 32℃-48℃ adjustment |
| Seat Power | 45W |
| Power Cable Length | 1.5M |
| Hose Connection | 1/2" |
| Material | Plastic |
| Safety Devices | Float switch, temperature sensor, temperature fuse |
6. Setup and Installation
Installation of the Eapmic Smart Electric Bidet Seat is designed to be straightforward. No specialized plumbing tools are typically required. Ensure you have access to a standard AC110V power outlet near the toilet.
- Prepare the Toilet: Turn off the water supply to your toilet and flush to empty the tank. Remove your existing toilet seat and lid. Clean the toilet bowl rim thoroughly.
- Install Mounting Plates: Place the provided mounting plates over the toilet bowl holes. Secure them with the bolts and washers.
- Attach Bidet Seat: Slide the bidet seat onto the mounting plates until it clicks into place. Ensure it is firmly seated and aligned.
- Connect Water Supply:
- Disconnect the existing water supply hose from the toilet tank's fill valve.
- Install the 1/2" 3-way connector to the toilet tank's fill valve.
- Connect the toilet's original water supply hose to one outlet of the 3-way connector.
- Connect the provided water inlet tube (approx. 31.5 inches) from the bidet seat to the remaining outlet of the 3-way connector.
- Restore Water Supply: Slowly turn on the water supply to the toilet. Check for any leaks at all connection points.
- Connect Power: Plug the bidet seat's power cord into a grounded AC110V electrical outlet.
- Initial Check: Perform a quick check of all functions as described in the "Operating Instructions" section.
Image: The bidet seat and its various connection parts, illustrating the components involved in the installation process.
7. Operating Instructions
The bidet seat features an intuitive control panel for easy operation. Ensure you are seated on the bidet seat for functions to activate due to the built-in body sensor.
7.1 Basic Washing Functions
- Rear Wash: Press the "Rear Wash" button for posterior cleansing.
- Feminine Wash (Bidet): Press the "Feminine Wash" button for anterior cleansing.
- Stop: Press the "Stop" button to cease any washing or drying function.
7.2 Adjustments
- Water Temperature: Use the "Water Temp" buttons to cycle through the 4 temperature settings (OFF, 33℃, 36℃, 40℃).
- Water Pressure: Use the "Water Pressure" buttons (usually indicated by +/-) to increase or decrease the spray intensity.
- Nozzle Position: Use the "Nozzle Position" buttons (usually indicated by arrows) to adjust the nozzle forward or backward.
- Air Dryer Temperature: Use the "Dryer Temp" buttons to adjust the warm air temperature (32℃-48℃).
- Seat Temperature: Use the "Seat Temp" buttons to adjust the heated seat temperature.
7.3 Special Functions
- Oscillation: While a wash function is active, press the "Oscillate" button to enable oscillating nozzle movement. Press again to stop.
- Massage: While a wash function is active, press the "Massage" button for a pulsating water stream. Press again to stop.
- Deodorization: The automatic deodorization function activates automatically when the body sensor detects a user.
Image: A close-up view of the bidet seat's control panel, showing the various buttons for wash, temperature, and position adjustments.
8. Maintenance
Regular cleaning and maintenance will ensure the longevity and optimal performance of your bidet seat.
- Cleaning the Bidet Seat:
- Unplug the bidet seat from the power outlet before cleaning.
- Wipe the exterior surfaces with a soft, damp cloth and a mild, non-abrasive cleaner.
- Do not use harsh chemicals, abrasive pads, or solvents, as these can damage the finish.
- Nozzle Cleaning: The nozzles are self-cleaning. If manual cleaning is required, gently pull out the nozzles and wipe them with a soft brush or cloth. Do not use excessive force.
- Water Filter: The bidet seat includes a water filter. Periodically check the filter for debris and replace it as needed to maintain water quality and bidet performance. Refer to the filter's specific instructions for replacement frequency.
- Long-Term Storage: If the bidet seat will not be used for an extended period, unplug it, turn off the water supply, and drain any remaining water from the unit to prevent freezing or stagnation.
9. Troubleshooting
If you encounter any issues, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| No power | Power cord unplugged, circuit breaker tripped, power outage. | Ensure power cord is securely plugged in. Check circuit breaker. Verify power supply. |
| No water spray | Water supply valve closed, water inlet tube kinked, water filter clogged, body sensor not activated. | Open water supply valve. Straighten water inlet tube. Clean or replace water filter. Ensure you are properly seated on the bidet. |
| Water temperature not adjusting | Incorrect setting, heating element issue. | Verify water temperature setting. If issue persists, contact customer support. |
| Seat not heating | Incorrect setting, heating element issue. | Verify seat temperature setting. If issue persists, contact customer support. |
| Leaks from connections | Loose connections, damaged seals. | Tighten all water connections. Check for damaged washers or seals and replace if necessary. |
If the problem persists after attempting these solutions, please contact Eapmic customer support.
10. Warranty and Support
Eapmic products are manufactured with quality and reliability in mind. For warranty information and customer support, please refer to the warranty card included with your purchase or visit the official Eapmic website. If you have any questions or require assistance, please do not hesitate to contact our customer service team.
Customer Service Contact: Please refer to your purchase documentation or the manufacturer's website for the most current contact information.