Laney CUB-SUPER12
Laney CUB-SUPER12 Amplifier User Manual
Model: CUB-SUPER12 | Brand: Laney
Introduction
The Laney CUB-SUPER12 is a versatile all-tube combo amplifier designed for guitarists seeking authentic tube tone in a compact and portable package. It features a single channel with a comprehensive three-band EQ, a dynamic footswitchable boost function, and an onboard reverb. The amplifier is equipped with a custom-designed HH 12-inch driver and offers flexible power options, allowing operation at either 15 watts or less than 1 watt for various playing environments.
Key Features
- Selectable Power Output: 15W or <1W for versatile use.
- Custom Voiced Speaker: Features a 12-inch HH custom voiced driver.
- All-Tube Design: Equipped with 3 x 12AX7 preamp tubes and 2 x EL84 output tubes.
- Integrated Reverb: Footswitchable on-board reverb for added depth.
- Dynamic Boost: Footswitchable boost function for lead tones.
- Effects Loop: Insert style FX loop for external effects pedals.
- External Speaker Output: Allows connection to an external speaker cabinet.
Setup
Unpacking and Inspection
Carefully remove the amplifier from its packaging. Inspect the unit for any signs of damage that may have occurred during transit. Retain all packaging materials for future transport or servicing.
Placement
Place the CUB-SUPER12 on a stable, flat surface. Ensure adequate ventilation around the amplifier to prevent overheating. Avoid placing the unit near heat sources or in direct sunlight. For optimal sound projection, position the amplifier at ear level or slightly angled upwards.
Power Connection
- Ensure the amplifier's power switch is in the OFF position.
- Connect the supplied power cable to the AC input on the rear panel of the amplifier.
- Plug the other end of the power cable into a grounded electrical outlet.
- Before powering on, ensure your guitar is connected and all volume controls are set to minimum.
The Laney CUB-SUPER12 amplifier positioned next to an electric guitar, ready for use.
Operating Instructions
Front Panel Controls
The front panel provides access to all primary sound shaping controls.
- Power Switch: Turns the amplifier on and off.
- Input Jacks (15W / <1W): Connect your guitar to either the 15W input for full power or the <1W input for reduced output, ideal for home practice.
- Gain: Controls the amount of pre-amp gain, affecting the level of distortion.
- Bass: Adjusts the low-frequency response of the amplifier.
- Middle: Adjusts the mid-frequency response, crucial for shaping the guitar's presence.
- Treble: Adjusts the high-frequency response, controlling brightness.
- Reverb: Controls the level of the built-in digital reverb effect.
- Volume: Controls the overall output volume of the amplifier.
- Boost: Activates the footswitchable boost function for increased gain.
Detailed view of the amplifier's front panel, showing all control knobs and input jacks.
Rear Panel Connections
The rear panel provides essential connections for external devices.
- FX Send/Line Out: Output for sending signal to external effects or a mixing console.
- FX Return: Input for receiving signal from external effects.
- Footswitch (FS2): Connect an optional footswitch to control the Boost and Reverb functions remotely.
- External Speaker: Connect an external speaker cabinet (ensure correct impedance matching).
The rear panel of the CUB-SUPER12, highlighting the effects loop and speaker connections.
Maintenance
Proper maintenance ensures the longevity and optimal performance of your Laney CUB-SUPER12.
- Cleaning: Use a soft, dry cloth to clean the exterior of the amplifier. Avoid abrasive cleaners or solvents.
- Tube Care: As an all-tube amplifier, the tubes will eventually need replacement. If you notice a decrease in performance or unusual noise, consult a qualified technician for tube inspection and replacement.
- Storage: When not in use, store the amplifier in a cool, dry place away from extreme temperatures and humidity.
- Ventilation: Always ensure the amplifier has adequate ventilation during operation to prevent overheating.
Troubleshooting
This section addresses common issues you might encounter with your CUB-SUPER12.
| Problem | Possible Cause | Solution |
|---|---|---|
| No Sound | Power not connected, volume low, faulty cable, standby mode. | Check power cable, increase volume, test cables, ensure amp is out of standby. |
| Weak or Distorted Sound | Worn tubes, incorrect impedance, speaker damage. | Consult technician for tube check, verify speaker impedance, inspect speaker. |
| Excessive Noise/Hum | Ground loop, faulty tubes, external interference. | Try different power outlet, check cables, consult technician for tube check. |
| Boost/Reverb Not Working | Footswitch not connected, internal issue. | Ensure footswitch is correctly plugged in, if issue persists, seek service. |
If the problem persists after attempting these solutions, please contact Laney customer support or a qualified service technician.
Specifications
| Feature | Detail |
|---|---|
| Model Number | CUB-SUPER12 |
| Output Wattage | 15 Watts (selectable to <1W) |
| Preamp Tubes | 3 x 12AX7 |
| Output Tubes | 2 x EL84 |
| Speaker | 12-inch HH Custom Voiced Driver |
| Controls | Volume, Reverb, Treble, Middle, Bass, Gain, Boost |
| Connectivity | 6.35mm Jack (Inputs, FX Send/Return, Footswitch, External Speaker) |
| Item Weight | 28.4 pounds |
| Product Dimensions | 20.2 x 19 x 12 inches |
| Color | Black |
Warranty and Support
The Laney CUB-SUPER12 amplifier comes with a manufacturer's warranty. For detailed information regarding warranty terms, coverage, and duration, please refer to the warranty card included with your product or visit the official Laney Amplification website. For technical support, service inquiries, or to purchase accessories, please contact Laney customer service directly or reach out to your authorized dealer.
You can find more information and contact details on the official Laney website: www.laney.co.uk
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.