Introduction
This manual provides comprehensive instructions for the safe and proper installation, operation, and maintenance of your Perlegear Full Motion TV Wall Mount (Model PGMF13). Please read this manual thoroughly before beginning installation to ensure correct setup and to prevent potential damage or injury. Keep this manual for future reference.
Product Features
- Wide Compatibility: Supports most 26-50 inch TVs and computer monitors with a maximum weight of 55 lbs. Compatible VESA mounting patterns range from 75x75mm to 300x300mm.
- Versatile Mounting Options: Designed for installation on concrete, brick, and wood stud walls. Note: Not recommended for drywall-only installation.
- Maximized Flexibility: Enjoy optimal viewing angles with +/-90° swivel, -15° to +5° tilt for glare reduction, and 90° locking intervals for landscape to portrait rotation. Features +/-3° post-installation leveling.
- Space-Efficient Design: Retracts to a compact 3.39 inches from the wall and extends up to 14.49 inches, allowing flexible TV positioning even in tight corners.
- Dependable Stability: Constructed from alloy steel and rigorously tested to 4 times its rated load capacity, ensuring secure support for your valuable electronics. UL Listed for safety.
Package Contents
Before installation, please verify that all components listed below are present and undamaged. If any parts are missing or defective, contact Perlegear customer support immediately.
Figure 1: Included hardware and support materials.
| Component | Description | Quantity |
|---|---|---|
| Wall Plate Assembly | Pre-assembled articulating arm and wall plate. | 1 |
| TV Brackets | Vertical bars that attach to the back of the TV. | 2 |
| Hardware Pack | Assorted screws, washers, spacers, and anchors for various TV and wall types. | 1 set |
| Bubble Level | For ensuring level installation. | 1 |
| Cable Ties | For cable management. | 3 |
| User Manual | This instruction guide. | 1 |
Installation Guide
Follow these steps carefully for a secure and successful installation. It is recommended to have a second person assist with lifting and mounting the TV.
1. Prepare the TV
- Carefully place your TV face down on a soft, clean surface to prevent scratches.
- Identify the VESA mounting holes on the back of your TV.
- Attach the TV brackets to the back of your TV using the appropriate screws, washers, and spacers from the hardware pack. Ensure the brackets are securely fastened and evenly aligned.
Figure 2: Attaching TV brackets to the television.
2. Mount the Wall Plate
- Determine the desired mounting height and location on your wall. Use a stud finder to locate a wood stud, or ensure you are mounting on solid concrete or brick.
- Position the wall plate against the wall at the desired height and use the included bubble level to ensure it is perfectly horizontal. Mark the pilot hole locations.
- Drill pilot holes at the marked locations. The drill bit size will vary depending on your wall type (refer to the detailed instructions in the included manual for specific drill bit sizes).
- Secure the wall plate to the wall using the appropriate lag bolts and washers. Tighten them firmly, but do not overtighten.
Figure 3: Wall types compatible with the Perlegear TV mount.
Figure 4: Securely mounted wall plate.
3. Hang the TV
- With assistance, carefully lift the TV with the attached brackets and hook them onto the wall plate's arms.
- Ensure the TV is securely seated on the mount. Use the safety screws or locking mechanisms (if applicable) to prevent accidental dislodgement.
Video: "Sturdy & Easy to install tv mount for TVs and Monitors" - This video demonstrates the installation process and the mount's stability.
Operating Instructions
Your Perlegear TV mount offers various adjustments for optimal viewing.
- Swivel: Gently push or pull the TV to swivel it left or right up to +/-90 degrees. This allows for flexible viewing from different areas of the room.
- Tilt: Loosen the tilt adjustment screws on the TV brackets, adjust the screen to your desired tilt angle (-15° to +5°), and then re-tighten the screws to secure the position. This helps reduce glare.
- Extension/Retraction: Pull the TV away from the wall to extend it up to 14.49 inches, or push it back towards the wall to retract it to 3.39 inches.
- Rotation: The mount allows for 90° rotation, enabling you to switch between landscape and portrait orientation. Ensure the locking intervals are engaged for stability.
- Leveling: For minor adjustments after installation, the mount offers +/-3° post-install leveling. Refer to the detailed manual for specific leveling screw locations.
Figure 5: Demonstrating the mount's tilt, swivel, and extension features.
Figure 6: TV screen rotated to portrait orientation using the mount's rotation feature.
Maintenance
Regular maintenance ensures the longevity and safe operation of your TV mount.
- Cleaning: Wipe the mount with a soft, dry cloth to remove dust. Avoid using abrasive cleaners or solvents.
- Check Connections: Periodically check all screws and bolts to ensure they remain tight. Re-tighten if necessary, but do not overtighten.
- Inspect for Damage: Regularly inspect the mount for any signs of wear, damage, or corrosion. If any issues are found, discontinue use and contact customer support.
Troubleshooting
If you encounter any issues with your TV mount, refer to the common problems and solutions below. If the problem persists, contact Perlegear customer support.
| Problem | Possible Cause | Solution |
|---|---|---|
| TV is not level. | Wall plate not level or post-install leveling needed. | Use the +/-3° post-install leveling feature. If the wall plate itself is significantly off, you may need to re-mount it. |
| Mount feels loose or wobbly. | Mounting bolts are not tight enough or incorrect wall type. | Ensure all lag bolts securing the wall plate are tightened. Verify that the mount is installed on a solid wood stud, concrete, or brick wall, not drywall alone. |
| Difficulty adjusting swivel or tilt. | Joints are too tight or screws are overtightened. | Loosen the relevant adjustment screws slightly. Do not loosen excessively to maintain stability. |
Specifications
- Model: PGMF13
- Screen Size Compatibility: 26 - 50 inches
- Maximum Load Capacity: 55 lbs (25 kg)
- VESA Compatibility: 75x75mm, 100x100mm, 100x200mm, 150x150mm, 200x100mm, 200x200mm, 250x250mm, 300x300mm
- Tilt Range: -15° to +5°
- Swivel Range: +/-90°
- Rotation: 90° (with locking intervals)
- Leveling Adjustment: +/-3°
- Wall Distance (Retracted): 3.39 inches (86 mm)
- Wall Distance (Extended): 14.49 inches (368 mm)
- Material: Alloy Steel
- Color: Black
- Certifications: UL Listed
Warranty and Support
Perlegear is committed to providing high-quality products and excellent customer service. Your TV mount comes with a standard warranty (details available on the official Perlegear website or included warranty card).
For any questions, concerns, or technical assistance, please contact our US-based support team:
- Website: Perlegear Official Store
- Email: [Insert Customer Support Email Here, if available]
- Phone: [Insert Customer Support Phone Number Here, if available]
Please have your model number (PGMF13) and purchase information ready when contacting support.
