Saxby Lighting 90954
Saxby Orbital PRO CCT Fire Rated Downlight User Manual
Model: 90954 | Brand: Saxby Lighting
Introduction
The Saxby Orbital PRO downlight features advanced Colour Changing Technology (CCT), allowing you to select between warm white (3000K), cool white (4000K), and daylight white (6000K) light outputs. This versatile downlight is designed for easy installation and provides efficient, indirect LED illumination. Its slim, patented design is fire-rated and IP65 rated, making it suitable for various indoor environments, including bathrooms. It is supplied with a dimmable Eaglerise driver compatible with leading and trailing edge dimmers.
Key Features:
- Colour Changing Technology (CCT): Easily switch between 3000K (Warm White), 4000K (Cool White), and 6000K (Daylight White).
- High Lumen Output: Two SMD LED modules project 450 lumens of indirect LED light.
- Anti-Glare Dome: Unique design for comfortable illumination.
- Fire Rated: Enhanced safety for peace of mind.
- IP65 Rated: Suitable for zones 1 and 2 in bathrooms and other areas where water spray is possible.
- Dimmable: Supplied with a compatible Eaglerise driver.
- Compact Design: Slim profile with a projection of only 3mm.
Package Contents
Please check the package contents carefully. If any items are missing or damaged, contact your supplier immediately.
- Saxby Orbital PRO Downlight Unit
- Eaglerise Dimmable LED Driver
- Mounting Hardware (Screws)
- User Manual (this document)
Safety Information
Always ensure the mains power supply is switched off before commencing any installation or maintenance work. Installation should only be carried out by a qualified electrician in accordance with current wiring regulations. Do not modify the product in any way. Ensure proper earthing where required.
- Voltage: 220-240V AC, 50/60Hz
- IP Rating: IP65 (Protected against dust ingress and low-pressure water jets from any direction)
- Fire Rating: Suitable for use in fire-rated ceilings.
- Insulation: Can be covered with insulation.
Setup and Installation
Follow these steps for safe and correct installation of your Saxby Orbital PRO downlight.
- Preparation:
- Switch off the mains electricity supply at the consumer unit/fuse box.
- Ensure the installation area is clear of obstructions and existing wiring.
- Determine the desired location for the downlight.
- Cut-out:
Using a suitable hole saw, cut a circular hole in the ceiling with a diameter of 97mm. Ensure the hole is clean and free of debris.
- Wiring:
- Connect the mains supply cable to the provided Eaglerise LED driver. Ensure correct polarity: Live (L), Neutral (N), and Earth (E) if applicable.
- The downlight unit is pre-wired to the driver. Do not attempt to disconnect or modify this connection.
- Ensure all connections are secure and insulated.
- Colour Temperature Selection (Pre-installation):
Before inserting the downlight into the ceiling, locate the small switch on the side of the downlight unit or driver. This switch allows you to select the desired colour temperature: 3000K (Warm White), 4000K (Cool White), or 6000K (Daylight White). Set this to your preferred option before final installation.
Image: Saxby Orbital PRO downlight emitting warm white light (3000K). This image shows the downlight with a soft, yellowish glow, typical of warm white illumination.
Image: Saxby Orbital PRO downlight emitting cool white light (4000K). This image displays the downlight with a neutral, slightly bluish-white light, characteristic of cool white illumination.
Image: Saxby Orbital PRO downlight emitting daylight white light (6000K). This image shows the downlight with a bright, crisp white light, similar to natural daylight.
- Mounting:
Carefully push the spring clips on the sides of the downlight upwards and insert the downlight into the cut-out hole. The clips will spring back down, securing the downlight in place against the ceiling.
- Final Check:
Ensure the downlight is flush with the ceiling and securely fitted. Restore power at the consumer unit/fuse box.
Operating Instructions
Once installed, operating the Saxby Orbital PRO downlight is straightforward.
Changing Colour Temperature (CCT):
The colour temperature is set via a switch on the downlight unit or driver during installation. To change the colour temperature after installation, you will need to remove the downlight from the ceiling to access this switch. It is recommended to select your preferred colour temperature before final installation.
Dimming Functionality:
The Saxby Orbital PRO downlight is supplied with a dimmable LED driver. It is compatible with most leading edge and trailing edge dimmers. For optimal performance and to avoid flickering or buzzing, ensure your dimmer switch is suitable for LED lighting and has a compatible load range. Consult the dimmer manufacturer's instructions for specific wiring and operation details.
Maintenance
The Saxby Orbital PRO downlight requires minimal maintenance.
- Cleaning: To clean the downlight, ensure the power is switched off. Use a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these may damage the finish or electrical components.
- LED Lifespan: The integrated LED module has an average lifespan of 30,000 hours and is non-replaceable.
- Inspection: Periodically inspect the downlight for any signs of damage or loose connections. If any issues are found, switch off the power and consult a qualified electrician.
Troubleshooting
If you experience issues with your Saxby Orbital PRO downlight, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. | No power supply; loose wiring; faulty switch; faulty driver. | Check mains power and circuit breaker. Verify all wiring connections are secure. Test the switch. If issues persist, consult a qualified electrician. |
| Light flickers or buzzes when dimmed. | Incompatible dimmer switch; dimmer load too low/high. | Ensure your dimmer is suitable for LED lighting and matches the wattage requirements. Try a different type of LED-compatible dimmer. |
| Incorrect colour temperature. | CCT switch set incorrectly. | Switch off power, carefully remove the downlight, and adjust the CCT switch to the desired setting (3000K, 4000K, or 6000K). Reinstall. |
| Light is dim or inconsistent. | Dimmer setting too low; wiring issue; driver issue. | Adjust dimmer to maximum. Check wiring connections. If problem persists, the driver may be faulty and require replacement by a qualified electrician. |
Specifications
| Feature | Detail |
|---|---|
| Brand | Saxby Lighting |
| Model Number | 90954 |
| Item Weight | 258 g |
| Material | Die cast aluminium alloy & steel |
| Finish Type | Matt white paint |
| Colour | White |
| Voltage | 220-240 Volts |
| Wattage | 9 watts |
| Type of Bulb | LED (SMD 2835) |
| Luminous Flux | 450 Lumen |
| Colour Temperature | 3000K (Warm White), 4000K (Cool White), 6000K (Daylight White) |
| Dimmable | Yes (with compatible leading/trailing edge dimmers) |
| Average Life | 30,000 Hours |
| IP Rating | IP65 |
| Cut Hole Diameter | 97mm |
| Overall Diameter | 110mm |
| Projection | 3mm |
| Included Components | Mounting Hardware, Screws, User Manual |
Warranty and Support
For warranty information and technical support, please refer to the documentation provided with your purchase or contact Saxby Lighting directly through their official website or customer service channels. Keep your proof of purchase for warranty claims.
Light Bulb Recycling: For information on recycling this and other types of lamps, please consult local recycling guidelines or visit relevant environmental agency websites.
Light Bulb Breakage and Clean Up: In the event of breakage, follow local guidelines for cleaning up and disposing of broken or damaged lamps. Avoid direct contact with broken glass and dispose of materials safely.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.