Introduction
Welcome to the instruction manual for your Aerocool Mirage 12 Pro PC Case Fan kit. This manual provides essential information for the proper installation, operation, and maintenance of your new 3 x 120mm Addressable RGB (ARGB) fans and H66F RGB Hub. Please read this manual thoroughly before proceeding with installation to ensure optimal performance and safety.
Image: The Aerocool Mirage 12 Pro PC Case Fan kit, showcasing three ARGB fans, the H66F RGB hub, and the included remote control. The fans feature a vibrant, customizable lighting effect.
Package Contents
Verify that all items listed below are present in your package:
- 3 x Aerocool Mirage 120mm ARGB Fans
- 1 x H66F 6-Port RGB Hub with PWM Control
- 1 x Remote Control for RGB and Fan Speed
- Mounting Screws for Fans
- Cables for Hub Connection (e.g., SATA power, ARGB sync cable)
Safety Information
Please observe the following safety guidelines:
- Always disconnect power from your computer before installing or removing any components.
- Handle components with care to avoid damage.
- Ensure proper cable routing to prevent interference with moving parts or airflow.
- Do not expose the hub or fans to moisture or extreme temperatures.
Setup and Installation
Follow these steps to install your Aerocool Mirage 12 Pro fans and H66F RGB Hub:
- Prepare Your System: Power off your computer and disconnect it from the power outlet. Open your PC case to access the internal components.
- Install the Fans: Mount the 120mm fans into your desired fan locations within the PC case (e.g., front, top, rear). Use the provided mounting screws. The fans are equipped with anti-vibration pads to minimize noise.
- Connect Fans to H66F Hub: Connect each 6-pin fan cable from the Mirage fans to the corresponding 6-pin ports on the H66F RGB Hub. The hub supports up to six fans.
- Connect H66F Hub to Power: Connect the SATA power connector from your PC's power supply unit (PSU) to the H66F RGB Hub. This provides power to both the fans and the RGB lighting.
- Connect H66F Hub to Motherboard (Optional ARGB Sync): If you wish to synchronize the fan's RGB lighting with your motherboard's software, connect the hub's 5V ARGB cable to a compatible 3-pin 5V ARGB header on your motherboard. Ensure it is a 5V ARGB header, not a 12V RGB header, to prevent damage.
- Cable Management: Route all cables neatly to improve airflow and aesthetics within your PC case.
- Close Case and Power On: Once all connections are secure, close your PC case and reconnect the power. Power on your computer.
Image: Three Aerocool Mirage 120mm ARGB fans, viewed from the front, illustrating their design and readiness for mounting within a PC case.
Image: A detailed view of the Aerocool H66F RGB Hub, highlighting its multiple connection ports for fans and ARGB accessories, as well as the power input.
Operating Instructions
Your Aerocool Mirage 12 Pro fans can be controlled via the included remote control or, if connected, through your motherboard's ARGB software.
Using the Remote Control
The remote control allows you to adjust fan speed and RGB lighting effects. Ensure the remote has a working battery.
Image: A detailed view of the Aerocool RGB remote control, displaying its array of buttons for controlling fan speed, lighting modes, colors, and brightness.
- Power Button: Turns the RGB lighting on or off.
- PWM Button: Toggles between PWM fan speed control modes. The H66F hub provides PWM control functions for optimized fan speed.
- MANUAL Button: Activates manual control for lighting effects.
- HUB Button: Switches control to the H66F hub's internal lighting modes.
- MOBO Button: Switches control to motherboard ARGB software (if connected to a compatible header).
- MODE / COLOR / SPEED Buttons: Adjust the lighting mode, color, and effect speed.
- ASTRO / AUTO / RAINBOW Buttons: Select specific pre-programmed ARGB lighting effects.
- Brightness Buttons (Sun icons): Adjust the brightness level of the RGB lighting.
- Lock Button: Locks the current lighting settings.
Motherboard Software Control
If you connected the H66F Hub to your motherboard's 5V ARGB header, you can use your motherboard's proprietary RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, Gigabyte RGB Fusion, ASRock Polychrome Sync) to customize the lighting effects. Ensure the remote control is set to 'MOBO' mode or the hub is configured for motherboard control.
RGB Lighting Features
The Aerocool Mirage 12 Pro fans feature an infinity mirror design and a single RGB LED ring, creating a captivating visual effect.
Image: A close-up view of three Aerocool Mirage 12 Pro fans, highlighting the mesmerizing infinity mirror effect created by their ARGB lighting and central acrylic design.
- Infinity Mirror Design: An acrylic mirror in the center of the fan, combined with the RGB LED ring, creates an illusion of infinite depth.
- Addressable RGB (ARGB): Each LED can be controlled individually, allowing for complex and dynamic lighting patterns.
- Multiple Effects: Choose from a variety of pre-set effects via the remote control or customize extensively with motherboard software.
Maintenance
Regular maintenance helps ensure the longevity and optimal performance of your fans:
- Dust Cleaning: Periodically clean dust from the fan blades and housing using compressed air or a soft brush. Ensure the PC is powered off before cleaning.
- Connection Check: Occasionally check that all cables are securely connected to the fans, hub, and motherboard.
- Environmental Conditions: Operate the fans within recommended temperature and humidity ranges to prevent damage.
Troubleshooting
If you encounter issues with your Aerocool Mirage 12 Pro fans, refer to the following common problems and solutions:
- Fans Not Spinning:
- Ensure the PC is powered on.
- Verify that the H66F Hub is correctly connected to the PSU via a SATA power cable.
- Check that all 6-pin fan cables are securely connected to the H66F Hub.
- RGB Lighting Not Working:
- Check the remote control battery and ensure it is functioning.
- If using motherboard control, ensure the hub's ARGB cable is connected to a 5V ARGB header and the remote is set to 'MOBO' mode.
- Confirm that the RGB lighting is not turned off via the remote control or motherboard software.
- Excessive Noise:
- Ensure fans are securely mounted using the anti-vibration pads.
- Check for any cables or obstructions interfering with the fan blades.
- Dust accumulation can cause noise; clean the fans if necessary.
- PWM Control Behavior:
- The H66F hub provides PWM control functions for fan speed optimization. If experiencing stepped fan speed control, ensure your motherboard's BIOS/UEFI settings are configured for PWM control on the connected fan header.
Specifications
| Feature | Specification |
|---|---|
| Model Number | MIRAGE12PRO |
| Fan Dimensions | 120mm x 120mm x 25mm (4.72"L x 4.72"W x 0.98"H) |
| Power Connector Type | 6-Pin (for fans to hub) |
| Hub Power Connector | SATA Power |
| ARGB Sync Connector | 3-Pin 5V ARGB |
| Rated Voltage | 12 Volts |
| Rated Wattage | 4.2 watts |
| Cooling Method | Air Fan |
| Noise Level | 17.8 Decibels |
| Maximum Rotational Speed | 1300 RPM |
| Compatible Devices | Desktop PCs |
| Material | Metal (frame), Acrylic (mirror design) |
Warranty and Support
For warranty information and technical support, please refer to the official AeroCool website or contact your retailer. Keep your proof of purchase for warranty claims.
AeroCool Official Website: www.aerocool.io
