Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your FRANKE 112.0551.361 Siphon Grey. Designed for single sinks, this bottle trap ensures efficient drainage and prevents odors from entering your living space. Please read this manual thoroughly before installation and use to ensure proper function and longevity of the product.
The FRANKE 112.0551.361 is a high-quality bottle trap with a wall connection diameter of 40 mm, crafted from durable stainless steel in a grey finish.
Product Overview
Figure 1: FRANKE 112.0551.361 Siphon Grey. This image shows the complete siphon assembly, including the main vertical trap, the horizontal pipe connecting to the sink drain, and the side connection for overflow or other appliances. The grey color and stainless steel material are visible.
The FRANKE 112.0551.361 Siphon is a compact and efficient bottle trap designed to fit under single kitchen sinks. Its design allows for easy inspection and cleaning, ensuring hygienic operation.
Setup and Installation
Before beginning installation, ensure you have all necessary tools and components. It is recommended to have a bucket or towel ready to catch any residual water from existing plumbing.
Components Checklist:
- FRANKE 112.0551.361 Siphon assembly
- Sealing gaskets (pre-installed or separate)
- Connection nuts
Installation Steps:
- Preparation: Turn off the water supply to the sink. If replacing an old siphon, place a bucket underneath and carefully disconnect the old unit. Clean the sink drain opening and the wall connection point.
- Assemble the Siphon: Connect the horizontal pipe of the siphon to the sink's drain outlet. Ensure all gaskets are correctly seated and tighten the connection nut hand-tight, then use a wrench for a final quarter turn, being careful not to overtighten.
- Connect to Wall Drain: Connect the vertical outlet of the siphon to the wall drain pipe. The wall connection diameter is 40 mm. Adjust the length and angle of the pipes as needed to ensure a proper fit. Secure all connections with appropriate nuts and gaskets.
- Side Connections (Optional): If connecting a dishwasher or washing machine, use the designated side inlet. Ensure a secure, leak-free connection. If not used, ensure the cap is securely in place.
- Leak Test: Once all connections are secure, turn on the water supply and fill the sink. Allow water to drain and carefully inspect all connections for any leaks. Tighten any leaking connections as necessary.
Note: For optimal performance, ensure all connections are clean and free of debris before assembly.
Operating Instructions
The FRANKE 112.0551.361 Siphon operates automatically as water drains from the sink. Its primary function is to create a water seal that prevents sewer gases from entering your home.
- Ensure the sink drain is clear of large debris before draining water.
- The bottle trap design allows for easy access to clear blockages if they occur within the trap itself.
Maintenance
Regular maintenance will ensure the longevity and efficient operation of your FRANKE siphon.
Cleaning the Siphon:
- Disassembly: Place a bucket underneath the siphon. Unscrew the bottom cap of the bottle trap.
- Cleaning: Remove any accumulated debris, food particles, or hair from inside the trap. Rinse the cap and the interior of the trap with warm, soapy water.
- Reassembly: Securely reattach the bottom cap, ensuring the gasket is properly seated to prevent leaks.
- Test: Run water through the sink to check for leaks.
Frequency: It is recommended to clean the siphon every 3-6 months, or more frequently if slow drainage is observed.
General Care:
- Avoid pouring harsh chemicals down the drain, as they can damage the siphon material and gaskets.
- Do not dispose of large food scraps or grease down the sink, as this can lead to blockages.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Slow Drainage | Accumulation of debris in the trap or drain pipe. | Clean the siphon trap as described in the Maintenance section. If the problem persists, the blockage may be further down the drain pipe. |
| Leaking Connections | Loose connection nuts or improperly seated gaskets. | Ensure all connection nuts are tightened securely. Check that gaskets are correctly positioned and not damaged. Replace damaged gaskets if necessary. |
| Unpleasant Odors | Dry trap (water seal evaporated) or debris buildup. | Run water down the sink to refill the trap. Clean the siphon trap to remove any odor-causing debris. Ensure the siphon is correctly installed to maintain the water seal. |
If you encounter issues not listed here or if solutions do not resolve the problem, please contact FRANKE customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | 112.0551.361 |
| Brand | FRANKE |
| Product Type | Siphon / Bottle Trap |
| Color | Grey |
| Material | Stainless Steel |
| Dimensions (L x W x H) | 30 x 20 x 15 cm |
| Item Weight | 380 g |
| Wall Connection Diameter | 40 mm |
| Compatibility | For single sinks |
Warranty and Support
FRANKE products are manufactured to the highest quality standards. For information regarding warranty coverage and customer support, please refer to the official FRANKE website or contact your local distributor.
When contacting support, please have your product model number (112.0551.361) and purchase date available.
For further assistance, visit the official FRANKE website: www.franke.com
