Electraline 59219 Advanced Digital Programmable Thermostat User Manual

1. Introduction

The Electraline 59219 Advanced Digital Programmable Thermostat is designed to provide precise and efficient temperature control for your home's heating and cooling systems. Featuring 24 daily time zones and three customizable temperature levels (Comfort, Energy Saving, and Holiday/Antifreeze), this wall-mounted thermostat helps optimize energy consumption and maintain a comfortable indoor environment. Its digital display and touch control method ensure ease of use and clear readability.

2. Safety Information

• Electrical Safety: Installation should only be performed by a qualified electrician. Ensure the main power supply is disconnected before installation or maintenance to prevent electric shock.
• Battery Handling: Use only the specified battery type (2x AA, 1.5V). Do not mix old and new batteries, or different types of batteries. Dispose of used batteries responsibly according to local regulations.
• Placement: Install the thermostat away from direct sunlight, drafts, and heat sources (e.g., radiators, lamps) to ensure accurate temperature readings.
• Cleaning: Use a soft, dry cloth for cleaning. Do not use abrasive cleaners or solvents.

3. Setup

3.1. Battery Installation

The thermostat requires 2 AA (1.5V) batteries for operation. These are not included with the product.

1. Gently open the battery compartment cover, usually located on the back or side of the unit.
2. Insert two AA 1.5V batteries, ensuring correct polarity (+ and -) as indicated inside the compartment.
3. Close the battery compartment cover securely.

3.2. Mounting and Wiring

This is a wall-mounted thermostat with a 3-wire connection. Ensure the power supply is OFF before proceeding with wiring.

1. Separate the mounting plate from the thermostat unit.
2. Position the mounting plate on the desired wall location, ensuring it is level and away from heat sources or drafts. Mark the drilling points.
3. Drill holes and insert wall plugs (if necessary). Secure the mounting plate to the wall using screws.
4. Connect the thermostat wires to the appropriate terminals on the mounting plate. Refer to the wiring diagram provided in the product packaging for specific connections (L, N, NO, NC).
5. Carefully attach the thermostat unit to the mounted plate, ensuring it clicks securely into place.

Figure 1: Electraline 59219 Digital Thermostat mounted on a wall.

4. Operating Instructions

The Electraline 59219 thermostat features a digital display and touch controls for easy operation.

4.1. Basic Controls

• Power Button: Turns the thermostat ON or OFF.
• Up/Down Arrows: Adjust temperature settings or navigate menu options.
• Mode Button: Cycles through operating modes (e.g., Auto, Manual, Program).
• Program Button: Accesses programming settings for time and temperature schedules.

4.2. Setting Time and Date

To set the current time and day of the week:

1. Press and hold the 'Clock' or 'Time' button (refer to your specific unit's button labels). The minutes display will start flashing.
2. Use the Up/Down arrows to adjust the minutes.
3. Press the 'Clock' or 'Time' button again. The hour display will flash. Use the Up/Down arrows to adjust the hour.
4. Press the 'Clock' or 'Time' button once more. The day of the week will flash. Use the Up/Down arrows to select the current day.
5. Press the 'Clock' or 'Time' button again to confirm and exit.

4.3. Programming Temperature Schedules

The thermostat allows for 24 daily time zones to set three temperature levels: Comfort, Energy Saving, and Holiday (Antifreeze).

1. Press the 'Program' button to enter programming mode.
2. Use the Up/Down arrows to select the desired day or group of days for programming (e.g., Mon-Fri, Sat-Sun, or individual days).
3. Press the 'Program' button again to select the first time zone. The time will flash.
4. Use the Up/Down arrows to set the start time for this period.
5. Press the 'Mode' button to select the desired temperature level (Comfort, Energy Saving, or Holiday/Antifreeze) for this period.
6. Use the Up/Down arrows to set the target temperature for the selected level.
7. Repeat steps 3-6 for all 24 time zones for the selected day(s).
8. Once all periods are programmed, press the 'Program' button repeatedly until you exit programming mode, or wait for the thermostat to automatically save and return to normal operation.

4.4. Temperature Control Range

The thermostat controls temperature within a range of 5°C to 30°C.

5. Maintenance

• Cleaning: Regularly wipe the thermostat's surface with a soft, dry cloth to remove dust. Avoid using liquid cleaners that could seep into the device.
• Battery Replacement: When the low battery indicator appears on the display, replace both AA batteries promptly to ensure continuous operation and prevent loss of settings.
• Inspection: Periodically check the wiring connections for any signs of wear or damage.

6. Troubleshooting

• No Display/Thermostat Not Responding: Check if batteries are correctly inserted and not depleted. Replace batteries if necessary. Ensure the power supply to the heating/cooling system is active.
• Incorrect Temperature Reading: Ensure the thermostat is not exposed to direct sunlight, drafts, or heat sources. Allow some time for the thermostat to stabilize after installation.
• Heating/Cooling Not Activating: Verify that the thermostat is in the correct operating mode (e.g., 'Auto' or 'Heat'/'Cool' mode) and that the set temperature is appropriate for activation. Check the wiring connections.
• Programming Issues: If programs are not running as expected, re-enter programming mode and carefully review all time and temperature settings for each period.

7. Specifications

8. Warranty and Support

For warranty information and technical support, please refer to the documentation included in your product packaging or visit the official Electraline website. Keep your purchase receipt as proof of purchase for any warranty claims.