1. Introduction
This manual provides essential information for the proper setup, operation, and maintenance of your Festool Interface-Pad IP-STF-D220/48-LHS 2 225. Please read these instructions carefully before use to ensure optimal performance and safety.
The Festool Interface-Pad IP-STF-D220/48-LHS 2 225 is designed to achieve perfect, streak-free sanding results. Its eccentric movement capability ensures a smooth finish. This interface pad offers easy replacement in case of wear, eliminating the need to replace the entire sanding pad assembly.
2. Product Overview
The Festool Interface-Pad is a crucial component for achieving high-quality sanding finishes, particularly when working with specific materials and applications. It provides a flexible layer between the sanding pad and the abrasive, enhancing the sanding process.
2.1 Components Included
- 1 x Festool Interface-Pad IP-STF-D220/48-LHS 2 225
- 8 x Plastic Screws for attachment
Image 1: Festool Interface-Pad IP-STF-D220/48-LHS 2 225 with included plastic screws.
Image 2: Top view of the Festool Interface-Pad, showing the hole pattern for dust extraction and attachment.
3. Setup
The interface pad is designed for quick and easy installation onto your compatible Festool sanding pad.
3.1 Compatibility
This interface pad is specifically suitable for the PLANEX LHS 2 225 EQ(I) wall sander. It is not compatible with the PLANEX LHS 225 EQ (models up to 09/2020) or the PLANEX LHS-E 225 EQ. It must be used in combination with the ST-D220/48-LHS 2 225 sanding pad.
3.2 Attaching the Interface Pad
- Ensure your sanding pad (ST-D220/48-LHS 2 225) is clean and free of debris.
- Align the Festool Interface-Pad IP-STF-D220/48-LHS 2 225 with the sanding pad, ensuring the holes for the screws and dust extraction align perfectly.
- Insert the 8 included plastic screws into the designated holes.
- Tighten the plastic screws. A second screw or a coin can be used to turn and secure them; no special screwdriver is required. Ensure all screws are snug to prevent movement during operation.
4. Operating Instructions
Once the interface pad is securely attached, you can proceed with your sanding tasks.
4.1 Attaching Abrasives
The interface pad features a StickFix hook-and-loop surface. Simply press your compatible StickFix abrasive disc onto the interface pad, ensuring it is centered and securely attached. The hook-and-loop system allows for quick and easy changing of abrasive discs.
4.2 Sanding Applications
This interface pad is ideal for achieving perfect, streak-free surfaces. Its design supports the eccentric movement of the sander, which is crucial for fine finishing. It is primarily used for:
- Working with plaster and dispersion putties
- Paint preparation and finishing
- Drywall construction
- Restoration projects
5. Maintenance
Proper maintenance will extend the life of your Festool Interface-Pad.
- Cleaning: After each use, gently brush off any dust or debris from the interface pad, especially from the StickFix surface and the dust extraction holes.
- Inspection: Regularly inspect the interface pad for signs of wear, damage, or deformation. Check the plastic screws for any signs of stripping or damage.
- Replacement: The interface pad is designed for easy replacement in case of wear. If you notice a decrease in sanding quality, excessive vibration, or visible damage, replace the interface pad promptly.
- Storage: Store the interface pad in a clean, dry environment, away from direct sunlight and extreme temperatures.
6. Troubleshooting
While the interface pad is a simple component, some issues might arise.
| Problem | Possible Cause | Solution |
|---|---|---|
| Poor sanding finish / Streaks | Worn interface pad; Abrasive not properly attached; Incorrect abrasive grit. | Replace interface pad; Re-attach abrasive securely; Use appropriate grit for the task. |
| Abrasive disc detaches easily | Worn StickFix surface on interface pad; Dust/debris on StickFix surface. | Clean StickFix surface; Replace interface pad if hook-and-loop is no longer effective. |
| Excessive vibration during use | Interface pad not securely attached; Damaged or deformed interface pad. | Ensure all plastic screws are tightened; Replace interface pad. |
7. Specifications
| Attribute | Value |
|---|---|
| Model Number | 205418 |
| Product Dimensions | 0.39 x 0.39 x 0.39 inches |
| Item Weight | 4.23 ounces |
| Manufacturer | Festool |
| Grit Material (Abrasive) | Aluminum Oxide (typical for compatible abrasives) |
| Compatible Devices | Festool PLANEX LHS 2 225 EQ(I) |
8. Warranty and Support
Festool products are known for their quality and durability. This product comes with an All-inclusive warranty. For detailed information regarding warranty terms, registration, and support, please visit the official Festool website or contact Festool customer service.
For further assistance or technical support, please refer to the contact information provided with your Festool tools or visit the Festool official website: www.festool.com
