1. Introduction
Thank you for choosing the upHere SR12-06-6 120mm ARGB Case Fan. This 6-pack fan system is designed to provide efficient cooling and customizable RGB lighting for your PC case, CPU coolers, and radiator systems. This manual provides detailed instructions for installation, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your fans.
2. Package Contents
- 6 x upHere SR12-06 ARGB 120mm Case Fans
- 1 x Fan Control Hub
- 1 x Remote Control
- Mounting Screws
- User Manual (this document)
3. Features
- Customizable RGB LED Lighting: Equipped with 8 ultra-bright RGB LED lights, offering full lighting for your build with multiple control choices and various modes like breathing, static, and multi-color cycling.
- Unlimited Color Transformation: One key to change RGB color, providing a cool gaming experience with beautiful RGB effects and efficient heat dissipation.
- Long Service Life: Wear-resistant hydraulic bearing construction ensures quiet operation and increased air volume with an astounding service life of more than 40,000 hours.
- Optimized Fan Blades Design: The 9 blades are specifically designed for high-volume air delivery while maintaining a minimum noise level.
- Shock-Absorbing Silicone Pads: Equipped with shock-absorbing silicone pads to reduce noise generated by resonance.
4. Specifications
| Specification | Value |
|---|---|
| Size | 120mm x 120mm x 25mm |
| Fan Speed | 1180 ± 10% RPM |
| Noise Level | 19.9 dBA |
| Airflow Capacity | 41.2 CFM |
| Bearing Type | Hydraulic Bearing |
| Rated Voltage | DC 12V |
| Rated Power | 1.8 W |
| Power Connector Type | 3-Pin (for fan), SATA (for hub power), 5V ARGB (for motherboard sync) |
| Material | Copper (likely referring to motor windings) |
Note: Specifications are subject to change without prior notice.
Image: Dimensions of the upHere 120mm case fan.
Image: Detailed specifications of the upHere 120mm case fan.
5. Safety Information
- Always disconnect power from your PC before installing or performing maintenance on any components.
- Handle fans and cables with care to avoid damage.
- Ensure proper cable management to prevent interference with moving parts and to maintain good airflow.
- Do not attempt to modify the fans or control hub, as this may void your warranty and cause damage.
- Keep out of reach of children.
6. Setup & Installation
6.1 Fan Placement
Determine the optimal placement for your fans within your PC case for effective airflow. Common placements include front (intake), rear (exhaust), top (exhaust), and bottom (intake). Ensure the fan's airflow direction (indicated by arrows on the fan frame) matches your desired setup.
Image: Airflow direction of the upHere case fan.
6.2 Mounting Fans
- Align each fan with the desired mounting holes on your PC case, radiator, or CPU cooler.
- Secure the fans using the provided mounting screws. Do not overtighten.
- The fans are equipped with shock-absorbing silicone pads on the corners to minimize vibration and noise.
Image: upHere case fan with shock-absorbing silicone pad.
6.3 Connecting to the Control Hub
- Connect the 3-pin fan cables from each upHere fan to the corresponding ports on the fan control hub. Ensure the connectors are securely seated.
- Connect the SATA power cable from your PC's power supply unit (PSU) to the fan control hub. This provides power to all connected fans and RGB lighting.
- For motherboard ARGB synchronization, connect the 5V ARGB cable from the control hub to a compatible 5V 3-pin ARGB header on your motherboard. (Note: Do not connect to a 12V RGB header, as this will damage the LEDs.)
Image: Wiring diagram for upHere ARGB fans and control hub.
7. Operating Instructions
7.1 Remote Control Operation
The included remote control allows you to easily switch between multiple preset lighting effects and adjust fan speeds. Point the remote control towards the fan control hub for optimal response.
- ON/OFF: Power on/off the LED lighting.
- AUTO: Cycles through various preset lighting modes.
- S+/S-: Adjusts the speed of dynamic lighting effects.
- M+/M-: Cycles through different lighting modes.
- Color Buttons: Selects static colors (Red, Green, Blue, White, Yellow, Cyan, Purple, etc.).
- Brightness Buttons: Adjusts the brightness of the LED lighting.
- FAN+/FAN-: Adjusts the fan speed.
- M/B: Switches between remote control mode and motherboard sync mode.
Image: Remote control for upHere ARGB fans.
7.2 Motherboard ARGB Sync
If your motherboard has a compatible 5V 3-pin ARGB header and you have connected the control hub to it, you can synchronize the fan lighting with your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync). Use the 'M/B' button on the remote control to switch to motherboard sync mode.
Image: Motherboard ARGB Sync compatibility logos.
8. Maintenance
- Cleaning: Regularly clean the fan blades and frame to prevent dust buildup, which can reduce cooling efficiency and increase noise. Use a soft, dry cloth or compressed air. Ensure the PC is powered off and unplugged before cleaning.
- Connection Check: Periodically check all cable connections (fan to hub, SATA power, ARGB sync) to ensure they are secure and free from damage.
- Bearing Longevity: The hydraulic bearing is designed for long-term, maintenance-free operation. Avoid applying lubricants or disassembling the fan bearing.
Image: Hydraulic bearing of the upHere case fan.
9. Troubleshooting
- Fans not spinning:
- Ensure the fan control hub is correctly connected to the PSU via the SATA power cable.
- Check if individual fan cables are securely connected to the control hub.
- Verify that the PC is powered on.
- RGB lights not working:
- Ensure the fan control hub is receiving power via SATA.
- Check if the ARGB cable from the fan hub is correctly connected to a 5V 3-pin ARGB header on the motherboard (if using sync mode).
- If using remote control, ensure the remote has a working battery and is pointed towards the hub. Try pressing the 'ON' button.
- If in motherboard sync mode, ensure your motherboard's RGB software is running and configured correctly.
- Press the 'M/B' button on the remote to toggle between remote and motherboard control.
- Fans are too loud:
- Adjust fan speed using the remote control's 'FAN+'/'FAN-' buttons.
- Ensure fans are securely mounted and the silicone pads are in place to reduce vibration.
- Check for any obstructions to the fan blades.
- Inconsistent lighting/colors:
- Ensure all ARGB connections are firm.
- If using motherboard sync, check your motherboard's RGB software settings.
- If using remote, try resetting the mode or selecting a specific color.
10. Warranty & Support
upHere provides a worry-free 12-month warranty for the SR12-06-6 ARGB Case Fan. If you encounter any issues or have questions regarding your product, please contact upHere customer service for assistance. Please refer to the contact information provided on the product packaging or the official upHere website.