SEBSON Outdoor Wall Light with Motion Sensor (Model S-101012)

1. Introduction

Thank you for choosing the SEBSON Outdoor Wall Light with Motion Sensor. This product is designed to provide efficient and reliable outdoor illumination with the added convenience of automatic motion detection. Featuring integrated LEDs, a robust IP65 rating for outdoor use, and adjustable motion sensor settings, this light is suitable for various outdoor applications such as house walls, garages, and patios. Please read this manual carefully before installation and use to ensure proper function and safety.

Figure 1: SEBSON Outdoor Wall Light with Motion Sensor.

2. Safety Instructions

Please observe the following safety instructions to prevent injury or damage:

• Electrical Installation: Installation must be performed by a qualified electrician in accordance with local wiring regulations and safety standards.
• Power Disconnection: Always disconnect the power supply before installation, maintenance, or repair work.
• Voltage: Ensure the power supply voltage matches the product's requirements (230 Volts).
• IP65 Rating: This product is IP65 rated, meaning it is protected against dust ingress and low-pressure water jets from any direction. Ensure all connections are properly sealed during installation to maintain this rating.
• Integrated LEDs: The LEDs are integrated and non-replaceable. Do not attempt to open or modify the light fixture.
• Mounting Surface: Mount the light on a stable and suitable surface that can support its weight.
• Heat: The light fixture may become warm during operation. Do not touch it immediately after prolonged use.

3. Package Contents

The package includes:

• 2 x SEBSON Outdoor Wall Light with Motion Sensor
• 4 x Screws for fixing
• 4 x Wall plugs

4. Installation

Before beginning installation, ensure the power supply is switched off at the main circuit breaker.

1. Prepare Mounting Location: Choose a suitable location on a wall, ensuring it is within reach of the electrical wiring. Consider the desired detection range of the motion sensor (up to 9m at 1.80m - 2.50m height).
2. Mark Drill Holes: Use the light fixture's mounting plate as a template to mark the positions for the drill holes on the wall.
3. Drill Holes: Drill holes at the marked positions and insert the provided wall plugs.
4. Wiring: Connect the electrical wires from your mains supply to the terminals on the light fixture. Ensure correct polarity (Live, Neutral, Earth if applicable, though this is a double-insulated product). Secure all connections.
5. Mount the Fixture: Secure the light fixture to the wall using the provided screws. Ensure it is firmly attached.
6. Seal Connections: For outdoor use, ensure all cable entries and mounting points are properly sealed to maintain the IP65 weather resistance.
7. Restore Power: Once installation is complete and all connections are secure, restore power at the main circuit breaker.

Figure 2: Product dimensions (120mm x 65mm x 250mm).

Figure 3: Rear view of the light fixture with mounting plate.

5. Operating Instructions and Motion Sensor Settings

The SEBSON outdoor wall light features an integrated motion sensor with adjustable settings for optimal performance.

Figure 4: Key features including motion detection and programmability.

Motion Sensor Adjustment:

The motion sensor has two adjustable controls, typically located on the sensor unit itself. These controls allow you to customize the light's behavior:

• LUX (Light Sensitivity): This dial controls the ambient light level at which the sensor becomes active.
• Turn towards the sun symbol () for the light to activate in brighter conditions (daylight).
• Turn towards the moon symbol () for the light to activate only in darker conditions (dusk/night).
• The adjustable range is typically 3-2,000 LUX.
• TIME (Illumination Duration): This dial sets how long the light remains on after motion is detected and no further motion is sensed.
• Adjust from a minimum of 10 seconds to a maximum of 5 minutes.

Figure 5: Motion sensor with LUX and TIME adjustment dials.

Detection Range:

The motion sensor has a detection range of up to 9 meters and a detection angle of 140°. For optimal performance, install the light at a height between 1.80m and 2.50m.

Figure 6: Motion sensor detection range and angle.

6. Maintenance

To ensure the longevity and optimal performance of your SEBSON outdoor wall light, follow these maintenance guidelines:

• Cleaning: Regularly clean the light fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these can damage the finish or plastic components.
• Inspection: Periodically check the light for any signs of damage, loose connections, or wear. If any damage is found, disconnect power and consult a qualified electrician.
• No User-Serviceable Parts: The light contains no user-serviceable parts. Do not attempt to open the housing or replace the integrated LEDs.

7. Troubleshooting

If you encounter issues with your SEBSON outdoor wall light, refer to the following troubleshooting guide:

8. Specifications

9. Warranty and Support

This SEBSON product comes with a lifetime warranty, ensuring peace of mind regarding its quality and durability. For any questions, technical assistance, or warranty claims, please contact SEBSON customer support through the retailer where the product was purchased or visit the official SEBSON website for contact information.

Please retain your proof of purchase for warranty purposes.