1. Introduction
This manual provides essential instructions for the safe and effective use of your RPNB Model RP2002 Gun Security Safe. Please read this manual thoroughly before installation and operation to ensure proper functionality and security.
The RPNB Model RP2002 is designed to secure firearms, ammunition, and other valuables, featuring multiple access methods including biometric fingerprint, digital keypad, and emergency keys.
2. Important Safety Information
- Always store firearms unloaded within the safe.
- Keep emergency keys in a secure location away from the safe and out of reach of unauthorized individuals.
- Ensure the safe is securely mounted to prevent unauthorized removal.
- Do not store the safe in areas with extreme temperatures or high humidity.
- Regularly check battery levels to ensure continuous operation.
- Keep the fingerprint sensor clean and free from debris.
3. Package Contents
Verify that all components are present:
- RPNB Model RP2002 Gun Security Safe
- Emergency Keys (2)
- Mounting Hardware (screws, anchors)
- User Manual (this document)
4. Setup
4.1 Battery Installation
- Locate the battery compartment, typically on the inside of the safe door or rear panel.
- Insert the required batteries (usually AA, not included) according to the polarity indicators.
- Close the battery compartment cover securely.
4.2 Initial Code Setting
- With the safe door open, press the internal reset button (refer to diagram for location).
- Enter your desired 3-6 digit code on the keypad.
- Press the '#' or 'ENTER' button to confirm.
- Test the new code with the door open before closing.
4.3 Fingerprint Registration
- With the safe door open, press the internal reset button.
- Place your finger on the fingerprint sensor. The indicator light will flash.
- Lift and place your finger repeatedly (typically 5-10 times) at slightly different angles until the indicator light confirms successful registration (e.g., a green light or specific beep pattern).
- Repeat for additional fingerprints as desired. The safe supports multiple fingerprints.
- Test registered fingerprints with the door open before closing.
Figure 1: Safe opening methods including emergency keys, digital keypad, and biometric fingerprint.
Figure 2: Fingerprint registration process and sensor technology.
4.4 Mounting the Safe
The safe features pre-drilled holes for secure mounting. Use the included hardware to attach the safe to a flat surface such as a shelf, closet floor, or cupboard.
- Choose a secure and discreet location for mounting.
- Position the safe and mark the locations for the pre-drilled holes.
- Drill pilot holes if necessary, ensuring they are appropriate for the mounting hardware.
- Secure the safe using the provided screws and anchors.
Figure 3: Internal features including removable shelf and pre-drilled mounting holes.
5. Operating the Safe
5.1 Opening with Biometric Fingerprint
- Place a registered finger firmly on the fingerprint sensor.
- If recognized, the safe door will pop open rapidly.
5.2 Opening with Digital Keypad
- Enter your 3-6 digit code on the keypad.
- Press the '#' or 'ENTER' button.
- If the code is correct, the safe door will pop open rapidly.
5.3 Opening with Emergency Keys
In case of battery failure or forgotten codes/fingerprints, use the emergency keys.
- Locate the emergency keyhole, usually concealed near the keypad.
- Insert one of the emergency keys and turn it to unlock the safe.
Figure 4: Quick access via biometric fingerprint.
Figure 5: Interior view of the safe with contents.
6. Maintenance
6.1 Battery Replacement
The safe features a low battery warning indicator. When the red LED flashes or the safe emits a specific beep pattern during operation, replace the batteries promptly.
- Open the safe using a valid access method (code, fingerprint, or emergency key).
- Locate the battery compartment.
- Remove old batteries and insert new ones, ensuring correct polarity.
- Close the battery compartment.
6.2 Cleaning
- Wipe the exterior of the safe with a soft, dry cloth.
- Keep the fingerprint sensor and keypad free from dust, dirt, and moisture to ensure optimal performance.
7. Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Safe does not open with code/fingerprint. | Low batteries, incorrect code/fingerprint, sensor obstruction. | Replace batteries. Re-enter code carefully. Clean fingerprint sensor. Try emergency key. |
| Alarm sounds during operation. | Invalid code entered multiple times. | Enter correct code or use fingerprint/emergency key. The alarm will typically reset after a valid entry or a short period. |
| Fingerprint registration fails. | Finger not placed correctly, sensor dirty, fingerprint memory full. | Ensure finger covers the sensor completely. Clean sensor. If the light flashes RED 5 times with 10 beeps, the fingerprint storage capacity is full; consider deleting old fingerprints if supported by the model (refer to advanced settings if available). |
| Safe is unresponsive. | Completely drained batteries. | Use emergency keys to open the safe and replace batteries immediately. |
Figure 6: LED indicators for status and warnings.
8. Specifications
| Feature | Detail |
|---|---|
| Brand | RPNB |
| Model Name | RP2002 |
| Product Dimensions (D x W x H) | 9.84" x 11.02" x 8.07" |
| Item Weight | 5 Kilograms (11.02 lbs) |
| Capacity | Approximately 10.8 Pounds (internal volume) |
| Lock Type | Combination (Digital Keypad), Biometric (Fingerprint), Key |
| Color | Black |
| Material | Carbon Steel |
| Special Feature | Fingerprint Sensor |
| Mounting Type | Wall Mount (via pre-drilled holes) |
| Alarm | Anti-theft (for invalid code attempts) |
| Water Resistance Level | Not Water Resistant |
| UPC | 634769855009 |
Figure 7: External dimensions of the RPNB Model RP2002 Safe.
9. Warranty and Support
9.1 Warranty Information
Warranty details for the RPNB Model RP2002 Gun Security Safe are typically provided with your purchase documentation. Please retain your proof of purchase for warranty claims. For specific warranty terms and conditions, refer to the information included in your product packaging or contact RPNB customer service.
9.2 Customer Support
If you encounter any questions, difficulties, or require assistance with your RPNB safe, please contact RPNB customer support. Contact information can usually be found on the RPNB official website or within your product packaging.
