1. Introduction
Thank you for choosing the PARKSIDE PASA 20-Li Cordless Reciprocating Saw. This manual provides essential information for the safe and effective operation, maintenance, and troubleshooting of your tool. Please read this manual thoroughly before first use and keep it for future reference.
This cordless reciprocating saw is designed for powerful sawing in wood, plastic, and metal. It is part of the Parkside X 20 V Team series, compatible with all Parkside 20 V batteries (battery and charger not included).
Safety Notice: Always observe all safety warnings and instructions provided in this manual to prevent electric shock, fire, and serious injury.
2. Safety Instructions
2.1 General Power Tool Safety Warnings
- Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions may result in electric shock, fire, and/or serious injury.
- Keep your work area clean and well-lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
2.2 Electrical Safety
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
2.3 Personal Safety
- Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to battery pack, picking up or carrying the tool.
2.4 Power Tool Use and Care
- Do not force the power tool. Use the correct power tool for your application.
- Disconnect the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
- Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation.
3. Product Overview
The PARKSIDE PASA 20-Li is a versatile cordless reciprocating saw designed for various cutting tasks. It features an ergonomic design with a softgrip handle for comfortable use and a tool-free blade change system.
Image 1: The PARKSIDE PASA 20-Li Cordless Reciprocating Saw, shown with its detachable branch clamp and a black carrying case. The saw is green and black, featuring a long body and a prominent blade at the front.
3.1 Components
- Saw Blade
- Blade Holder / Chuck
- Serrated Clamping Support / Branch Clamp Attachment
- Softgrip Handle
- Trigger Switch
- Ignition Lock Button
- Battery Slot
- Ventilation Openings
4. Setup
4.1 Battery Installation
The PARKSIDE PASA 20-Li operates with a 20V battery from the Parkside X 20 V Team series (not included). Recommended batteries are 20 V 2 Ah or 20 V 4 Ah.
- Ensure the tool is switched off and the ignition lock is engaged.
- Slide the fully charged battery pack into the battery slot at the rear of the tool until it clicks securely into place.
- To remove the battery, press the release button on the battery pack and slide it out.
4.2 Blade Installation
The saw features a tool-free, self-clamping chuck for quick blade changes.
- Ensure the battery is removed for safety.
- Rotate the blade holder (chuck) counter-clockwise and hold it.
- Insert the saw blade fully into the opening until it locks.
- Release the blade holder. Gently pull on the blade to ensure it is securely fastened.
- To remove a blade, rotate the blade holder counter-clockwise and pull the blade out.
4.3 Attaching the Branch Clamp
The serrated clamping support (branch clamp) can be attached for better stability when cutting branches.
Image 2: A close-up view of the serrated branch clamp attachment, made of silver-colored metal with sharp teeth designed to grip branches securely during cutting.
- Align the clamp with the mounting points on the front of the saw.
- Slide the clamp onto the saw until it clicks into place.
- Ensure it is firmly attached before use.
- To remove, press the release tabs and slide the clamp off.
5. Operation
5.1 Switching On/Off
- To switch on: Press and hold the ignition lock button, then press the trigger switch.
- To switch off: Release the trigger switch. The ignition lock button will automatically reset.
5.2 Speed Control
The PARKSIDE PASA 20-Li features a continuously adjustable stroke rate. The harder you press the trigger switch, the higher the stroke rate (0-2700 rpm). This allows for precise control depending on the material and task.
5.3 Cutting Techniques
Always ensure the workpiece is securely clamped or stable before cutting. Apply light, steady pressure and let the saw do the work.
Image 3: A person wearing work gloves is using the PARKSIDE PASA 20-Li cordless reciprocating saw to cut a tree branch in an outdoor setting. The saw is actively cutting through the wood.
- Wood and Plastic: Use appropriate blades for wood or plastic. For pruning, the serrated clamping support can help stabilize branches. Start with a lower speed and increase as needed.
- Metal: Use specific metal-cutting blades. Apply cutting oil or coolant to prolong blade life and improve cutting performance. Maintain a moderate speed.
- Plunge Cutting: For plunge cuts into wood or soft materials, ensure the blade is sharp. Position the tool with the shoe plate resting on the workpiece, then slowly pivot the tool into the material.
6. Maintenance
6.1 Cleaning
- Always remove the battery pack before cleaning.
- Keep the ventilation openings clean to prevent overheating. Use a soft brush or compressed air.
- Wipe the tool housing with a damp cloth. Do not use harsh cleaning agents or solvents.
6.2 Blade Replacement
Refer to section 4.2 for detailed instructions on tool-free blade installation and removal. Always use sharp, undamaged blades suitable for the material being cut.
6.3 Storage
Store the tool in a dry, well-ventilated area, out of reach of children. Remove the battery pack before storing for extended periods. The included carrying case provides excellent protection for storage and transport.
Image 4: A black, robust carrying case with the 'PARKSIDE' logo embossed on the front. It features a red handle and metal latches, designed for secure storage and transport of the reciprocating saw and its accessories.
7. Troubleshooting
This section addresses common issues you might encounter with your PARKSIDE PASA 20-Li saw.
| Problem | Possible Cause | Solution |
|---|---|---|
| Tool does not start | Battery not inserted correctly Battery discharged Ignition lock not pressed | Ensure battery is fully clicked in Charge battery Press ignition lock button before trigger |
| Reduced cutting performance | Dull or damaged blade Incorrect blade for material Battery low | Replace blade Use appropriate blade Charge battery |
| Excessive vibration | Blade not securely fastened Damaged blade Workpiece not stable | Check blade installation Replace blade Secure workpiece firmly |
| Tool overheats | Blocked ventilation openings Overloading the tool | Clean ventilation openings Reduce cutting pressure; allow tool to cool |
8. Specifications
Technical data for the PARKSIDE PASA 20-Li Cordless Reciprocating Saw:
- Model: PASA 20-Li
- Power Source: Cordless, Battery-powered (20V Parkside X 20 V Team series)
- Motor: DC 580, Copper Winding
- Stroke Rate: 0-2700 rpm (continuously adjustable)
- Stroke Length: 20 mm
- Recommended Batteries: 20 V 2 Ah / 20 V 4 Ah (not included)
- Handle Material: Rubber (Softgrip)
- Item Weight: 2.97 Kilograms
- Special Features: Continuously adjustable stroke rate, tool-free blade change, serrated clamping support
- Surface Recommendation: Wood, Metal, Plastic
- Included Components: Saw (without battery/charger), 1 high-quality saw blade for green cuts (Swiss Made), serrated clamping support, carrying case.
9. Warranty and Support
This PARKSIDE product is manufactured with care and undergoes strict quality controls. While specific warranty details are not provided in this manual, please refer to your purchase documentation or the manufacturer's official website for information regarding warranty coverage and terms.
For technical support, spare parts, or service inquiries, please contact the retailer where you purchased the product or visit the official PARKSIDE service portal. Always provide the model number (PASA 20-Li) and ASIN (B08BJDD4XK) when seeking support.
