Aigostar Edward Multifunction Hair Clipper User Manual

Introduction

Thank you for choosing the Aigostar Edward Multifunction Hair Clipper. This comprehensive kit is designed for versatile grooming, allowing you to trim hair, shave beards, remove nose and ear hair, and manage body hair with precision and ease. Please read this manual thoroughly before first use to ensure safe and optimal operation.

Important Safety Instructions

• Keep the appliance dry. Do not use it near water or in wet conditions.
• Do not immerse the appliance in water.
• Ensure the power adapter is compatible with your local voltage before charging.
• Keep out of reach of children.
• Do not use if the appliance or any attachment is damaged.
• Only use original accessories and attachments provided by Aigostar.
• Unplug the appliance before cleaning.
• Avoid direct contact of blades with sensitive skin areas without appropriate guards.

Package Contents

Verify that all items listed below are present in your package:

• 1 x Aigostar Edward Main Trimmer Unit
• 5 x Cutting Heads (Precision Trimmer, Shaver, Hair Clipper, T-Blade, Nose/Ear Trimmer)
• 7 x Guide Combs (various lengths)
• 1 x Charging Adapter
• 1 x Storage Base
• 1 x Cleaning Brush
• 1 x Lubricating Oil

Product Overview

The Aigostar Edward trimmer features a robust design with a powerful motor and sharp blades for efficient grooming. Its cordless operation provides flexibility, and the interchangeable heads offer comprehensive functionality.

Setup and Initial Use

Charging the Appliance

1. Before first use, fully charge the trimmer for approximately 8 hours.
2. Connect the charging adapter to the trimmer and plug it into a power outlet.
3. The charging indicator light will illuminate during charging.
4. Once fully charged, disconnect the adapter.

Attaching and Detaching Cutting Heads

To change cutting heads:

1. Ensure the trimmer is turned off.
2. To detach, gently push the current head upwards from the front of the trimmer until it clicks off.
3. To attach, align the desired head with the trimmer body and press down until it securely clicks into place.

Attaching Guide Combs

Guide combs are used with the hair clipper head to achieve desired hair lengths.

• Select the appropriate guide comb for your desired length (e.g., 3mm, 6mm, 9mm, 12mm).
• Slide the comb onto the hair clipper head until it locks into position.
• To remove, gently pull the comb away from the head.

Operating Instructions

The trimmer operates with a single power button. Press to turn on, press again to turn off.

Hair Trimming

1. Attach the hair clipper head and the desired guide comb.
2. Turn on the trimmer.
3. Move the trimmer against the direction of hair growth for an even cut.
4. For precise lines, remove the guide comb and use the hair clipper head directly.

Beard Trimming and Shaving

1. For beard trimming, use the precision trimmer head or the T-blade head with a suitable guide comb.
2. For a close shave, attach the shaver head. Hold the shaver at a right angle to your skin and move it gently against the direction of hair growth.

Nose and Ear Hair Trimming

1. Attach the nose/ear trimmer head.
2. Gently insert the trimmer tip into your nostril or ear canal.
3. Move it in a circular motion to trim unwanted hair. Do not insert too deeply.

Body Hair Trimming

1. Use the hair clipper head with a guide comb or the T-blade head for body hair.
2. Always ensure the skin is taut and clean before trimming.

Maintenance and Cleaning

Cleaning the Blades

1. Turn off and unplug the trimmer.
2. Remove the cutting head.
3. Use the provided cleaning brush to remove any hair clippings from the blades and inside the head.
4. The blades can be rinsed under running water, but ensure the main unit remains dry. Allow blades to air dry completely before reattaching.

Oiling the Blades

1. After cleaning and drying, apply 1-2 drops of the provided lubricating oil onto the blades.
2. Turn on the trimmer for a few seconds to distribute the oil evenly.
3. Wipe off any excess oil with a soft cloth. Regular oiling ensures optimal performance and extends blade life.

Storage

Store the trimmer and its accessories in the provided storage base in a dry place, away from direct sunlight and extreme temperatures.

Troubleshooting

Technical Specifications

• Brand: Aigostar
• Model: Edward
• Power: 3W
• Motor Speed: 7000 rpm
• Power Source: Cordless (Rechargeable Battery)
• Charging Time: Approximately 8 hours
• Blade Material: Stainless Steel
• Dimensions: 23.2 x 15.2 x 6.9 cm
• Weight: 530 g
• Features: Multifunction, 5 Cutting Heads, 7 Guide Combs

Warranty and Customer Support

Aigostar products are manufactured to high-quality standards. For warranty information, please refer to the warranty card included in your package or visit the official Aigostar website.

If you encounter any issues or have questions regarding your Aigostar Edward Multifunction Hair Clipper, please contact our customer support team. Contact details can typically be found on the Aigostar website or on your purchase documentation.

Visit Aigostar Official Website