KLARUS XT32 1200 Lumens Flashlight User Manual

Introduction

Thank you for choosing the KLARUS XT32 1200 Lumens Flashlight. This manual provides detailed instructions to ensure safe and optimal use of your device. Please read it thoroughly before operation and retain it for future reference.

Image: KLARUS XT32 Flashlight kit showing the flashlight, two 18650 batteries, a K2 charger, a holster, a lanyard, and a USB charging cable.

Package Contents

• KLARUS XT32 Flashlight
• 2 x KLARUS 18650 2600mAh Rechargeable Batteries
• KLARUS K2 Dual-Slot Battery Charger
• Holster
• Lanyard
• USB Charging Cable
• Spare O-rings
• User Manual (this document)

Setup

1. Battery Installation

The KLARUS XT32 is designed to operate with 18650 or CR123A batteries. Ensure batteries are inserted with correct polarity.

1. Unscrew the tail cap of the flashlight counter-clockwise.
2. Insert two 18650 batteries (or four CR123A batteries) with the positive (+) terminal facing towards the head of the flashlight.
3. Screw the tail cap back on clockwise until securely tightened.

Image: The KLARUS XT32 flashlight shown alongside two 18650 batteries and four CR123A batteries, illustrating wide battery compatibility.

2. Battery Charging (for 18650 batteries)

Use the included KLARUS K2 charger to recharge the 18650 batteries.

1. Connect the K2 charger to a power source using the provided USB cable.
2. Insert the 18650 batteries into the charger slots, observing correct polarity.
3. The charger's indicator lights will show the charging status. Refer to the K2 charger's specific manual for detailed indicator information.
4. Once charging is complete, remove the batteries.

Operating Instructions

The XT32 features a patented dual tail-switch and a side switch for versatile operation.

Image: Detailed view of the KLARUS XT32's tail-switch and side switch, highlighting their respective functions for power, mode changes, and special modes.

Switch Functions

• Primary Tail Switch:
  • Momentary ON: Press and hold.
  • Constant ON/OFF: Click to turn on/off.
• Mode Tail Switch:
  • One-Touch Strobe: Press and hold (when flashlight is off or on).
  • One-Touch Low: Click (when flashlight is off).
• Side Switch:
  • ON/OFF: Click to turn on/off.
  • Mode Change: When on, click to cycle through brightness levels (Low-Medium-High-Turbo).
  • One-Touch Low: Press and hold (when flashlight is off).
  • One-Touch Turbo: Double-click (when flashlight is off or on).
  • Strobe: Triple-click (when flashlight is off or on).
  • SOS: Quadruple-click (when flashlight is off or on).
  • Lock-out Function: Press and hold the side switch for 5 seconds to lock/unlock.
  • Mode Memory: The flashlight will remember the last used brightness level (excluding Strobe/SOS).

Brightness Levels and Flash Modes

The XT32 offers four brightness levels and two special flash modes.

Image: Visual representation of the four lighting levels (Turbo, High, Medium, Low) and two flash modes (Strobe, SOS) of the KLARUS XT32, accompanied by a table of ANSI/NEMA FL1 standard data.

Note: Data is based on KLARUS 18650 2600mAh batteries. Actual performance may vary depending on batteries and environmental conditions.

Intelligent Battery Capacity Indicator

The side switch features a built-in battery capacity indicator to monitor the remaining power.

Image: The KLARUS XT32 flashlight with an overlay explaining the intelligent battery capacity indicator colors: Green (Over 70%), Orange (30-70%), Red (Less than 30%), Red Flashing (Less than 10%).

• Green: Battery capacity is over 70%.
• Orange: Battery capacity is between 30% and 70%.
• Red: Battery capacity is less than 30%.
• Red Flashing: Battery capacity is less than 10%. Recharge immediately.

Maintenance

• Cleaning: Clean the flashlight body with a soft, damp cloth. Do not use abrasive cleaners or solvents.
• Lubrication: Periodically apply silicone grease to the O-rings and threads to maintain waterproof sealing and smooth operation.
• Battery Care:
  • Remove batteries if the flashlight will not be used for an extended period to prevent leakage.
  • Store batteries in a cool, dry place.
  • Recharge 18650 batteries regularly, even if not fully depleted, to prolong their lifespan.
• Lens Care: Clean the lens with a lens cleaning cloth to remove dust or smudges. Avoid touching the lens directly.

Troubleshooting

If you encounter issues with your KLARUS XT32, please refer to the following common solutions:

• Flashlight does not turn on:
  • Ensure batteries are inserted with correct polarity.
  • Check if batteries are fully charged.
  • Tighten the tail cap and head of the flashlight securely.
  • Clean battery contacts with an alcohol swab if dirty.
  • Try different, known-good batteries.
• Light flickers or is dim:
  • Batteries may be low; recharge or replace them.
  • Ensure battery contacts are clean and free of corrosion.
  • Check for loose connections in the tail cap or head.
• Switches are unresponsive:
  • Check if the lock-out function is activated (for side switch). Deactivate by pressing and holding the side switch for 5 seconds.
  • Ensure the tail cap is fully tightened.

If problems persist, please contact KLARUS customer support.

Specifications

• Brand: KLARUS
• Model: XT32
• LED: CREE XP-L HI V3
• Maximum Output: 1200 Lumens
• Maximum Beam Distance: 1000 meters
• Power Source: 2 x 18650 batteries or 4 x CR123A batteries
• Working Voltage: 5-8.4V
• Reflector: Precision Manufactured Reflector
• Lens: Durable Tempered Glass with AR film plating for scratch resistance
• Material: 6061-T6 Aerospace Aluminum Alloy, Mil-SPEC HAIII Anodizing
• Waterproof Rating: IPX8 (underwater 2 meters)
• Impact Resistance: 1 meter

Image: An exploded view of the KLARUS XT32 flashlight highlighting its durable tempered glass lens, 6061-T6 aerospace aluminum alloy construction, grooved texture design, big side switch with battery indicator, and patented dual-switch tail cap.

Image: The KLARUS XT32 flashlight demonstrating its 1000-meter ultra long-range beam, emphasizing the precision manufactured reflector for improved spotlight and illumination performance.

Warranty and Support

KLARUS products are manufactured to high-quality standards. For warranty information or technical support, please refer to the official KLARUS website or contact your authorized dealer. Please retain your proof of purchase for warranty claims.

For further assistance, you may visit the KLARUS Brand Store on Amazon.

Safety Warnings

• Do not shine the flashlight directly into eyes. The powerful beam can cause temporary vision impairment or permanent eye damage.
• Keep out of reach of children.
• Do not disassemble the sealed head of the flashlight, as this may damage the light and void the warranty.
• Use only recommended batteries. Incorrect battery types or improper installation can cause damage or safety hazards.
• Avoid exposing the flashlight to extreme temperatures or direct sunlight for prolonged periods.