Introduction
This manual provides essential information for the safe installation, operation, and maintenance of your Amazon Basics Outdoor Wall Lantern with Integrated LED and Motion Sensor. Please read this manual thoroughly before installation and retain it for future reference.
Safety Information
WARNING: Risk of Electric Shock.
- Always turn off the power at the circuit breaker or fuse box before installation, servicing, or changing any part of the fixture.
- Consult a qualified electrician if you are unsure about the installation process.
- Ensure all electrical connections are made according to local codes and ordinances.
- Do not attempt to modify the fixture. Any modifications may void the warranty and create a safety hazard.
- This fixture is designed for outdoor use. Ensure proper sealing against moisture.
Package Contents
Verify that all components are present before beginning installation.
- Outdoor Wall Lantern with Integrated LED
- Mounting Bracket
- Mounting Screws
- Wire Nuts
- Instruction Manual
Image: The outdoor wall lantern shown with its mounting bracket, screws, and wire nuts.
Setup and Installation
- Prepare for Installation: Turn off power at the main circuit breaker. Ensure the power is off before proceeding.
- Remove Old Fixture (if applicable): Carefully disconnect and remove any existing light fixture.
- Attach Mounting Bracket: Secure the mounting bracket to the junction box using the provided screws. Ensure the bracket is level and firmly attached.
- Make Electrical Connections:
- Connect the black wire from the fixture to the black (hot) wire from the junction box using a wire nut.
- Connect the white wire from the fixture to the white (neutral) wire from the junction box using a wire nut.
- Connect the ground wire from the fixture to the ground wire from the junction box (or to the green ground screw on the mounting bracket) using a wire nut.
Ensure all connections are secure and no bare wire is exposed.
- Mount the Fixture: Carefully align the fixture with the mounting bracket and secure it using the provided screws. Ensure a tight seal against the wall to prevent moisture intrusion.
- Restore Power: Turn the power back on at the circuit breaker.
Image: Front view of the installed outdoor wall lantern, showing its design and integrated LED.
Image: Side view of the outdoor wall lantern, highlighting its upward-facing design and motion sensor at the base.
Operating Instructions
This outdoor wall lantern features an integrated motion sensor for automatic illumination.
Motion Sensor Functionality
- The motion sensor has a 120-degree detection angle and an 8-meter range.
- The light will activate when motion is detected within its range, typically at dusk or in low-light conditions.
- The duration the light stays on after motion detection can often be adjusted. Refer to the sensor's specific controls, usually small dials or switches located on the sensor itself, for time and sensitivity settings.
Image: A close-up view of the motion sensor located at the base of the lantern, showing its dome-shaped lens.
Adjusting Sensor Settings
The motion sensor typically has adjustable settings for sensitivity (how easily it detects motion) and time (how long the light stays on after detection). These adjustments are usually made via small dials on the sensor unit. Use a small screwdriver to carefully turn these dials to your desired settings.
Image: The outdoor wall lantern installed on a dark garage wall, providing illumination to the area below.
Maintenance
- Cleaning: Clean the fixture with a soft, damp cloth. Do not use abrasive cleaners or solvents, as they may damage the finish or plastic components.
- Integrated LED: The LED light source is integrated and not user-replaceable. If the LED fails, the entire fixture may need replacement.
- Inspection: Periodically inspect the fixture for any signs of damage, loose connections, or wear.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Light does not turn on. |
|
|
| Light stays on continuously. |
|
|
| Light flashes or flickers. |
|
|
Specifications
| Feature | Detail |
|---|---|
| Model Number | G10021P-NA |
| Dimensions (L x W x H) | 11.5" x 8.7" x 6.3" |
| Power Source | AC 120V |
| Wattage | 11W (Integrated LED) |
| Light Color | Warm White (3000 Kelvin) |
| Material | Aluminum (Fixture), Plastic (Shade) |
| Finish | Black |
| Motion Sensor Range | 120 degrees / 8 meters |
| Indoor/Outdoor Usage | Outdoor |
Warranty
This Amazon Basics Outdoor Wall Lantern is covered by a 3-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from accident, misuse, abuse, improper installation, or unauthorized repair.
For warranty claims, please retain your proof of purchase and contact customer support.
Customer Support
For technical assistance, troubleshooting, or warranty inquiries, please visit the Amazon Basics support page or contact Amazon customer service directly.
Online Support: Amazon Basics Store