Easytry123 Replacement Remote Control User Manual

Introduction

This manual provides instructions for the Easytry123 Replacement Remote Control, designed for use with various Fujitsu Air Conditioner models. This remote control offers essential functions for operating your air conditioning unit.

Important Note: This is a replacement remote control. While it is designed to replicate the primary functions of your original remote, some advanced or specific functions may not be fully supported. Please ensure your air conditioner model is listed above for compatibility.

Setup

1. Battery Installation

The remote control requires two (2) AAA batteries (not included). Follow these steps to install them:

1. Locate the battery compartment on the back of the remote control.
2. Slide the battery compartment cover downwards to open it.
3. Insert two AAA batteries, ensuring the positive (+) and negative (-) terminals align correctly with the markings inside the compartment.
4. Slide the battery compartment cover back into place until it clicks securely.

Image: Rear view of the remote control with the battery cover removed, revealing the two AAA battery slots. This illustrates where to insert the batteries.

2. Initial Use

This remote control operates using infrared technology and typically does not require any pairing. Once batteries are installed, point the remote control directly at your Fujitsu air conditioner unit and press the desired function button.

Operating Instructions

Familiarize yourself with the buttons on your remote control:

Image: Front view of the Easytry123 Replacement Remote Control. The image displays the LCD screen at the top, and various control buttons below, including 'START/STOP', 'MASTER CONTROL', 'FAN CONTROL', 'SET TEMP' arrows, 'TIMER', and other function buttons.

• START/STOP (Yellow Button): Press to turn the air conditioner unit ON or OFF.
• MASTER CONTROL: Cycles through various operating modes (e.g., Cool, Heat, Dry, Fan, Auto).
• FAN CONTROL: Adjusts the fan speed (e.g., Auto, Low, Medium, High).
• SET TEMP (Up/Down Arrows): Increases or decreases the desired temperature setting.
• AIR CLEAN: Activates or deactivates the air purification function, if available on your unit.
• COIL DRY: Initiates a coil drying function to prevent mold and odors.
• SLEEP: Activates the sleep mode, which adjusts temperature and fan speed for comfortable sleep and energy saving.
• SET: Used in conjunction with other buttons, possibly for confirming settings or adjusting specific parameters like fan direction.
• SWING (Left/Right Arrows): Controls the horizontal or vertical swing of the air deflector.
• TIMER MODE: Selects the timer function (e.g., ON Timer, OFF Timer).
• TIMER (+/- Buttons): Adjusts the timer settings (e.g., set delay time for ON/OFF).
• CLOCK ADJUST: Sets the current time on the remote's display.
• TEST RUN: For service or diagnostic purposes; typically not for regular user operation.
• RESET: Resets the remote control settings or clears error codes.

Maintenance

Cleaning the Remote Control

To clean the remote control, gently wipe its surface with a soft, dry cloth. For stubborn dirt, slightly dampen the cloth with water and a mild detergent, then wipe dry immediately. Do not use abrasive cleaners, alcohol, or solvents, as these can damage the remote's surface or internal components.

Battery Replacement

Replace batteries when the remote's range decreases, the display dims, or the unit no longer responds reliably. Always replace both batteries at the same time with new AAA batteries. Do not mix old and new batteries, or different types of batteries.

Storage

If the remote control will not be used for an extended period, remove the batteries to prevent leakage and potential damage to the remote.

Troubleshooting

• Remote not responding:
  • Check if the batteries are correctly installed and have sufficient charge. Replace if necessary.
  • Ensure there is a clear line of sight between the remote control and the air conditioner's receiver. Remove any obstructions.
  • Confirm that the remote is pointed directly at the air conditioner unit.
• Limited functionality:
  • As a replacement remote, some advanced or specific functions of your original air conditioner remote may not be supported. Refer to your air conditioner's original manual for specific features.
• Display issues:
  • If the display is dim or blank, replace the batteries.

Specifications

• Brand: Easytry123
• Compatible Devices: Fujitsu Air Conditioners (Models: ASYG14LECA, ASU9RMLQ, ASU12RMLQ, ASU18RMLQ, ARU12RML, AUU9RML, ART45LUAK, ASTG24LFCC, ASTA24LFCB, ASTA30JFCB)
• Connectivity Technology: Infrared
• Controller Type: Button Control
• Power Source: 2 x AAA Batteries (not included)
• Special Feature: Ergonomic design

Warranty and Support

For warranty information or technical support regarding your Easytry123 Replacement Remote Control, please refer to the retailer or manufacturer's official website where the product was purchased. Keep your purchase receipt as proof of purchase.