PEAKCOLD Stainless Steel Bar Glass Froster (Model IM25GF-S) User Manual

1. Introduction

Thank you for choosing the PEAKCOLD Stainless Steel Bar Glass Froster. This appliance is designed for commercial use to efficiently chill and frost glassware, plates, or other items to 0°F. This manual provides essential information for the safe installation, operation, maintenance, and troubleshooting of your unit. Please read these instructions thoroughly before use and retain them for future reference.

Front view of the PEAKCOLD Stainless Steel Bar Glass Froster with its top closed.

2. Important Safety Instructions

To reduce the risk of fire, electric shock, or injury when using your appliance, follow these basic precautions:

• Read all instructions before using the appliance.
• Connect to a grounded 110 Volt, 60 Hz electrical outlet only.
• Do not attempt to repair or replace any part of your appliance unless specifically recommended in this manual. All other servicing should be referred to a qualified technician.
• Keep ventilation openings in the appliance enclosure or in the built-in structure clear of obstruction.
• Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.
• Do not damage the refrigerant circuit.
• Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
• Unplug the appliance before cleaning or performing any maintenance.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

3. Package Contents

Verify that all items are present in the packaging:

• PEAKCOLD Bar Glass Froster Unit
• Wheels (Casters)
• Lock

4. Setup and Installation

4.1 Unpacking

Carefully remove all packaging materials, including foam and tape. Inspect the unit for any shipping damage. Report any damage immediately to your dealer.

4.2 Placement

Place the froster on a strong, level surface capable of supporting its weight (approximately 125 lbs). Ensure adequate ventilation around the unit. Maintain a minimum of 4 inches of clearance from walls or other objects on all sides to allow for proper airflow and heat dissipation. The exterior dimensions are 26.4" W x 26.4" D x 34.25" H.

Diagram showing the exterior dimensions of the PEAKCOLD Bar Glass Froster: 26.4 inches deep, 26.4 inches wide, and 34.25 inches high.

4.3 Caster Installation

Attach the included wheels (casters) to the bottom of the unit. Ensure they are securely fastened to allow for easy movement and positioning.

4.4 Initial Cleaning

Before first use, clean the interior and exterior of the froster with a mild detergent and warm water. Rinse thoroughly and dry completely.

4.5 Power Connection

After placement and cleaning, allow the unit to stand upright for at least 2-4 hours before plugging it into a grounded 110 Volt electrical outlet. This allows the refrigerant to settle, preventing potential compressor damage.

Rear view of the PEAKCOLD Bar Glass Froster, showing the power cord and ventilation grille.

5. Operating Instructions

5.1 Powering On

Once plugged in, locate the power switch, typically on the front or side of the unit, and turn it to the 'ON' position. The unit will begin to cool.

5.2 Temperature Control

The froster features a digital temperature control system. The factory preset temperature is 0°F, which is ideal for froster operation. Refer to the digital controller's specific instructions for adjusting the temperature if necessary.

5.3 Loading the Froster

Open the sliding top lids to access the interior. Arrange glassware or plates on the internal racks. The unit has a capacity for approximately (90) 8" mugs or (85) 10 oz. steins. Avoid overfilling to ensure proper air circulation and efficient frosting.

Top-down view of the PEAKCOLD Bar Glass Froster with the stainless steel lid open, revealing the interior storage racks.

Close-up view of the sliding stainless steel lids on the PEAKCOLD Bar Glass Froster, featuring handles and a lock.

An illustrative image demonstrating the internal capacity of a glass froster, showing multiple glasses stored within.

5.4 Achieving Optimal Frost

Allow sufficient time for items to reach the desired frosted temperature. The time required will vary depending on the initial temperature of the items and the ambient conditions.

A clear glass mug with a visible layer of frost on the outside, containing a beverage, sitting on a wooden table.

6. Maintenance

6.1 Cleaning the Interior and Exterior

Regular cleaning is crucial for hygiene and optimal performance. Unplug the unit before cleaning. Use a soft cloth with a mild, non-abrasive detergent and warm water to clean all surfaces. Rinse thoroughly and dry completely. Do not use harsh chemicals, abrasive cleaners, or sharp objects that could damage the stainless steel finish or interior components.

6.2 Automatic Defrost System

This unit is equipped with an automatic defrost system. This means that frost buildup on the evaporator coils is periodically melted and drained away. No manual defrosting is typically required. Ensure the drain line is clear and unobstructed to prevent water accumulation.

6.3 Condenser Coil Cleaning

Periodically clean the condenser coils located at the rear of the unit. Dust and debris can accumulate on the coils, reducing cooling efficiency and increasing energy consumption. Use a brush or vacuum cleaner to gently remove any buildup. Ensure the unit is unplugged before performing this task.

7. Troubleshooting

Before contacting service, check the following common issues:

8. Specifications

9. Warranty Information

The PEAKCOLD Stainless Steel Bar Glass Froster (Model IM25GF-S) comes with the following warranty:

• 1 Year Labor: Covers labor costs for repairs for one year from the date of purchase.
• 3 Year Parts: Covers replacement parts for three years from the date of purchase.
• 5 Year Compressor Part: Covers the compressor part for five years from the date of purchase.

Please retain your proof of purchase for warranty claims. For detailed warranty terms and conditions, refer to the official PEAKCOLD website or contact customer support.

10. Customer Support

For any questions, technical assistance, or service inquiries regarding your PEAKCOLD product, please contact our dedicated customer support team. We offer:

• US-Based Support Team
• In-House Parts & Servicing
• Setup & Programming Assistance
• Commercial & Residential Product Coverage

You can find contact information and additional resources on the official PEAKCOLD website: PEAKCOLD Store