1. Introduction
This manual provides essential instructions for the proper installation, operation, and maintenance of the Fargo 82700 Overlaminate Ribbon. This product is designed for use with Fargo DTC5500LMX and HDP6600 ID card printers to apply a protective 1.0 mil clear overlaminate layer to printed cards, enhancing durability and security. Adhering to these guidelines will ensure optimal performance and longevity of your overlaminate ribbon and printed cards.
Image of the Fargo 82700 Overlaminate Ribbon packaging, indicating its clear 1.0 mil overlaminate for 1000 images.
2. Safety Information
Please read and understand all safety precautions before handling or installing the overlaminate ribbon.
- Keep the ribbon out of reach of children.
- Do not expose the ribbon to direct sunlight or extreme temperatures. Store in a cool, dry place.
- Avoid touching the ribbon surface directly, as oils from skin can affect print quality. Handle by the edges of the cartridge.
- Ensure the printer is powered off and unplugged before installing or removing the ribbon.
- Dispose of used ribbons according to local environmental regulations.
3. Package Contents
The Fargo 82700 Overlaminate Ribbon package typically includes:
- One (1) Fargo 82700 Polyguard LMX 1.0 Mil Clear Overlaminate Ribbon cartridge.
- Capable of producing 1,000 images.
4. Setup and Installation
Follow these steps to properly install the Fargo 82700 Overlaminate Ribbon into your compatible Fargo printer (DTC5500LMX or HDP6600).
- Power Off Printer: Ensure your Fargo ID card printer is turned off and unplugged from the power source.
- Open Printer Cover: Open the printer's front or top cover to access the ribbon compartment. Refer to your printer's specific user manual for exact instructions on opening the cover.
- Remove Used Ribbon (if applicable): If a used ribbon is present, carefully remove it from the printer. Avoid touching the ribbon film.
- Unpack New Ribbon: Remove the new Fargo 82700 overlaminate ribbon cartridge from its packaging.
- Install Ribbon: Align the new ribbon cartridge with the designated slot in the printer. Gently push the cartridge into place until it clicks securely. Ensure it is seated firmly.
- Close Printer Cover: Close the printer cover securely.
- Power On Printer: Plug in and power on your printer. The printer will typically perform a self-test and recognize the new ribbon.
5. Operating Instructions
Once the Fargo 82700 Overlaminate Ribbon is installed, the printer will automatically detect it and prepare for lamination. The lamination process occurs after the card has been printed with color and/or monochrome panels. The printer's software or driver settings will allow you to configure lamination options, such as single-sided or dual-sided application, if supported by your printer model.
- Ensure your printer drivers are up-to-date for optimal performance.
- Select the appropriate lamination settings within your card design software or printer preferences.
- Load blank cards into the printer's input hopper.
- Initiate the print job. The printer will automatically apply the overlaminate after printing the card image.
6. Maintenance
Proper maintenance ensures consistent print quality and extends the life of your printer and ribbon.
- Printer Cleaning: Regularly clean your ID card printer according to the manufacturer's recommendations. Dust and debris can affect ribbon performance and card quality.
- Ribbon Storage: Store spare ribbons in their original packaging in a cool, dry environment, away from direct sunlight and heat sources.
- Avoid Contamination: Prevent dust, dirt, or fingerprints from coming into contact with the ribbon film.
7. Troubleshooting
Refer to the table below for common issues and their potential solutions.
| Issue | Possible Cause | Solution |
|---|---|---|
| Poor lamination quality (bubbles, uneven finish) | Dust on cards or printer rollers; incorrect printer settings; worn printer rollers. | Clean the printer thoroughly; verify lamination settings in software; contact support if rollers are worn. |
| Ribbon breakage | Improper installation; foreign object in printer; excessive tension. | Reinstall ribbon correctly; inspect printer for obstructions; ensure ribbon is not overtightened. |
| Printer does not recognize ribbon | Ribbon not seated correctly; faulty ribbon cartridge; outdated printer firmware. | Ensure ribbon is fully inserted; try a new ribbon; update printer firmware. |
8. Specifications
Key technical specifications for the Fargo 82700 Overlaminate Ribbon:
| Specification | Detail |
|---|---|
| Model Number | 82700 |
| Overlaminate Type | Polyguard LMX, Clear |
| Overlaminate Thickness | 1.0 mil |
| Images per Roll | 1,000 |
| Compatible Printers | Fargo DTC5500LMX, Fargo HDP6600 |
| Material Type | Polyvinyl Chloride |
| Item Weight | 8 ounces |
| Product Dimensions | 4 x 3 x 3 inches |
| Manufacturer | Fargo / HID Global |
9. Warranty and Support
For information regarding product warranty, technical support, or to purchase additional supplies, please refer to the official Fargo or HID Global website, or contact your authorized reseller. Keep your purchase receipt for warranty claims.
- Online Resources: Visit the HID Global website for product documentation, drivers, and FAQs.
- Technical Support: Contact HID Global technical support for assistance with product issues or troubleshooting beyond this manual.
- Authorized Resellers: Purchase genuine Fargo supplies from authorized resellers to ensure compatibility and quality.
