ID-COOLING SE-224-XT RGB CPU Cooler

1. Introduction

The ID-COOLING SE-224-XT RGB is a high-performance CPU air cooler designed to provide efficient heat dissipation for a wide range of Intel and AMD processors. Featuring four direct-contact heat pipes, a 120mm PWM fan with RGB lighting, and a robust heatsink design, this cooler offers an optimal balance of cooling capability, low noise operation, and aesthetic appeal.

The ID-COOLING SE-224-XT RGB CPU Cooler, showcasing its black heatsink, RGB fan, and overall compact design.

2. Safety Precautions

• Always disconnect power from your computer before installation or maintenance.
• Handle components with care to avoid damage to the CPU, motherboard, or cooler.
• Wear an anti-static wrist strap to prevent electrostatic discharge (ESD) damage to sensitive electronic components.
• Keep out of reach of children.
• Do not attempt to modify the cooler or its components.

3. Package Contents

Verify that all components are present in the package before beginning installation:

• ID-COOLING SE-224-XT RGB Heatsink
• 120mm PWM RGB Fan
• Universal Mounting Brackets (for Intel and AMD sockets)
• Backplate
• Mounting Screws and Spacers
• Thermal Paste
• Fan Clips
• RGB Splitter Cable (if included)

Components of the ID-COOLING SE-224-XT RGB CPU Cooler's mounting kit, including brackets, screws, and backplate, essential for secure installation on various CPU sockets.

4. Installation Guide

4.1. Preparation

1. Power off your computer and unplug the power cord.
2. Open your computer case and locate the CPU socket.
3. Remove any existing CPU cooler. Clean the CPU surface thoroughly to remove old thermal paste using isopropyl alcohol.
4. Identify the correct mounting hardware for your CPU socket (Intel LGA115X/1200/1700/2011/2066 or AMD AM4/AM5).

4.2. Mounting the Heatsink

1. Attach the appropriate mounting brackets to the heatsink base using the provided screws.
2. For AMD AM4/AM5, remove the plastic retention clips from the motherboard, but keep the original backplate. For Intel, install the universal backplate behind the motherboard, aligning the holes.
3. Apply a small pea-sized amount of thermal paste to the center of the CPU's integrated heat spreader (IHS).
4. Carefully place the heatsink onto the CPU, aligning the mounting holes with the standoffs or backplate. For AM4, it is recommended to screw in the top hole first loosely, then the bottom, before tightening both.
5. Secure the heatsink by tightening the spring-loaded screws in a diagonal pattern until snug. Do not overtighten.

Close-up view of the cooler's base, highlighting the four direct-contact copper heat pipes designed for efficient heat transfer from the CPU.

4.3. Installing the Fan

1. Attach the 120mm PWM RGB fan to the heatsink using the provided fan clips. Ensure the fan is oriented to blow air through the heatsink towards the rear exhaust of your case.
2. The fan features de-vibration rubber pads on its corners to reduce noise.

Close-up of the fan's corner, illustrating the de-vibration rubber pads integrated into the fan frame to minimize operational noise.

4.4. Connecting Cables

1. Connect the 4-pin PWM fan cable to the CPU_FAN header on your motherboard.
2. Connect the 4-pin 12V RGB cable to a compatible 12V RGB header on your motherboard. If your motherboard has multiple RGB headers, use the provided splitter cable if necessary.

The ID-COOLING SE-224-XT RGB CPU Cooler installed inside a PC case, with its RGB lighting illuminated, demonstrating its aesthetic integration.

5. Operation

5.1. Fan Control (PWM)

The 120mm fan supports Pulse Width Modulation (PWM), allowing your motherboard to dynamically control the fan speed based on CPU temperature. This ensures optimal cooling performance while minimizing noise during low-load operations. Fan speeds can range from 700 to 1800 RPM.

Image of the 120mm PWM fan, emphasizing its ability to adjust speeds between 700-1800 RPM for optimal balance between cooling performance and noise levels.

5.2. RGB Lighting

The integrated RGB lighting on the fan and heatsink can be controlled via your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light Sync, GIGABYTE RGB Fusion, ASRock Polychrome Sync). Ensure your motherboard has a 12V 4-pin RGB header for compatibility.

6. Maintenance

• Dust Removal: Periodically clean the heatsink fins and fan blades to prevent dust buildup, which can impede airflow and cooling performance. Use compressed air or a soft brush.
• Thermal Paste: The thermal paste typically lasts for several years. If you notice a significant increase in CPU temperatures, consider reapplying fresh thermal paste after cleaning the CPU and cooler base.
• Fan Inspection: Check the fan for any unusual noises or wobbling. Ensure the fan cables are securely connected.

7. Troubleshooting

• High CPU Temperatures:
  • Ensure the cooler is properly seated and tightened.
  • Verify that thermal paste was applied correctly and evenly.
  • Check for dust buildup on the heatsink fins and fan.
  • Confirm the fan is spinning and connected to the CPU_FAN header.
• Fan Not Spinning:
  • Check the 4-pin PWM cable connection to the motherboard's CPU_FAN header.
  • Ensure the fan is not obstructed.
  • Check BIOS settings for fan control.
• RGB Lighting Not Working:
  • Verify the 4-pin 12V RGB cable is correctly connected to a compatible 12V RGB header on the motherboard.
  • Ensure your motherboard's RGB software is installed and configured correctly.
  • Check for any loose connections or damaged pins on the RGB cable or header.

8. Technical Specifications

Diagram showing the CPU cooler's design ensures non-interference with RAM modules, even on Mini-ITX motherboards with tall memory sticks.

9. Warranty and Support

For warranty information and technical support, please refer to the official ID-COOLING website or contact their customer service directly. Keep your proof of purchase for warranty claims.

Official Website: www.idcooling.com