FPVDrone C330

Download PDF
Contents

FPVDrone Fli14+ 14CH Mini Receiver User Manual

Model: C330

Introduction

The FPVDrone Fli14+ is a compact and lightweight 2.4G 14-channel receiver designed for racing drones and other remote-controlled aircraft. It is compatible with Flysky AFHDS-2A protocol transmitters and offers RSSI output via OSD without requiring modifications. This receiver also provides telemetry for RSSI and RX battery voltage, and is optimized for Betaflight, supporting RSSI via Channel 14 (Aux10 in Betaflight).

Key features include:

  • Small and lightweight design, ideal for racing drones.
  • RSSI display via On-Screen Display (OSD) without requiring hacks.
  • Compatibility with Flysky AFHDS-2A protocol transmitters, including FS-i4, FS-i6, FS-I6X, FS-i6S, FS-i10, FS-iT4S, Eachine I6, Turnigy I6S, Turnigy Evolution, and Nirvana NV14.
  • Telemetry output for RSSI and RX Battery voltage.
  • Customized for Betaflight, supporting RSSI via Channel 14 (Aux10).

Setup

1. Antenna Placement

Proper antenna placement is crucial for optimal signal reception and range. Ensure the two receiver antennas are positioned at a 90-degree angle to each other. This configuration helps to minimize signal loss and improve overall link quality.

FPVDrone Fli14+ receiver with antennas positioned at 90 degrees

Image: The Fli14+ receiver with its two antennas clearly shown, illustrating the recommended 90-degree placement for optimal signal reception.

2. Wiring

Connect the receiver to your flight controller using the provided wiring harness. Ensure correct polarity and pin assignments (GND, VCC, IBUS). Refer to your flight controller's manual for specific wiring diagrams.

FPVDrone Fli14+ receiver with a 3-pin wiring harness connected

Image: The Fli14+ receiver connected to a standard 3-pin wiring harness (red, black, yellow wires), ready for connection to a flight controller.

3. Binding Procedure

To bind the Fli14+ receiver to your Flysky AFHDS-2A compatible transmitter:

  1. Power on the receiver while holding down the BIND button. The receiver's LED should flash rapidly, indicating it is in binding mode.
  2. Put your Flysky AFHDS-2A compatible transmitter into binding mode. Refer to your transmitter's manual for specific instructions.
  3. Once the binding is successful, the receiver's LED will turn solid.
  4. Power cycle both the receiver and the transmitter to confirm the binding.
Close-up of the FPVDrone Fli14+ receiver board showing the BIND button

Image: A detailed view of the Fli14+ receiver circuit board, highlighting the small 'BIND' button located near the connector.

4. Betaflight Configuration

For Betaflight integration, ensure your flight controller is configured to use IBUS for receiver input. The Fli14+ supports RSSI output via Channel 14, which corresponds to Aux10 in Betaflight. Configure your OSD settings in Betaflight to display RSSI from this channel.

Operating Instructions

After successful setup and binding, the Fli14+ receiver will communicate with your compatible Flysky AFHDS-2A transmitter. Ensure your transmitter is powered on before powering your aircraft to establish a stable link.

  • RSSI Display: The Received Signal Strength Indicator (RSSI) will be displayed on your OSD if configured correctly in Betaflight. Monitor this value during flight to ensure a strong signal.
  • Telemetry: The receiver transmits RSSI and RX battery voltage telemetry back to your compatible transmitter. This allows you to monitor critical flight parameters directly from your radio.
  • Range: Always perform a range check before flying, especially in new environments, to ensure safe operation.

Maintenance

To ensure the longevity and reliable performance of your Fli14+ receiver, follow these maintenance guidelines:

  • Keep Dry: Protect the receiver from moisture and humidity. Water damage can lead to malfunctions.
  • Cleanliness: Keep the receiver free from dust, dirt, and debris. Use a soft, dry brush or compressed air for cleaning.
  • Physical Protection: Mount the receiver securely within your aircraft to protect it from vibrations and impacts. Consider using heat shrink or a protective case.
  • Antenna Care: Avoid bending or damaging the antennas. Ensure they are securely attached and properly oriented.

Troubleshooting

If you encounter issues with your Fli14+ receiver, consider the following troubleshooting steps:

  • No Link/Binding Issues:
    • Ensure both receiver and transmitter are powered on and in binding mode correctly.
    • Verify that your transmitter is set to the AFHDS-2A protocol.
    • Check for physical damage to the receiver or antennas.
  • Poor Range/Signal Loss:
    • Re-check antenna placement and orientation (ensure 90-degree angle).
    • Ensure antennas are not obstructed by carbon fiber or other conductive materials.
    • Test in an open area away from potential interference sources (e.g., Wi-Fi routers, power lines).
  • No RSSI on OSD:
    • Verify Betaflight configuration for RSSI on Channel 14 (Aux10).
    • Ensure OSD elements are enabled and visible in Betaflight.
  • No Telemetry:
    • Confirm your transmitter supports and is configured for telemetry display.
    • Check wiring connections between the receiver and flight controller.

Specifications

ModelC330 (Fli14+)
Channels14CH
ProtocolFlysky AFHDS-2A
RSSI OutputYes, via OSD (Channel 14 / Aux10 in Betaflight)
Telemetry OutputRSSI & RX Battery
DimensionsApproximately 3.19 x 2.01 x 0.75 inches (Package Dimensions)
Weight0.528 ounces
ManufacturerFPVDrone

Warranty

For detailed warranty information, please refer to the official FPVDrone website or contact your point of purchase. Warranty terms and conditions may vary.

Support

For technical assistance, additional resources, or frequently asked questions, please visit the FPVDrone official support page or contact their customer service department. Contact information can typically be found on the manufacturer's website.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.