Absolute USA ABS95-7424 Double DIN Dash Kit and Wiring Harness Installation Manual

Introduction

This manual provides detailed instructions for the installation and use of the Absolute USA ABS95-7424 Double DIN Dash Kit, stereo harness, and antenna adapter package. This kit is designed to facilitate the installation of an aftermarket double DIN radio into specific 2008-2012 Nissan Titan vehicle models. Please read all instructions carefully before beginning the installation process.

Safety Information

• Always disconnect the vehicle's negative battery terminal before beginning any electrical installation to prevent short circuits and damage.
• Wear appropriate safety gear, including eye protection, during installation.
• Ensure all connections are secure and properly insulated to prevent electrical hazards.
• Consult a professional installer if you are unsure about any part of the installation process.
• Do not modify the vehicle's existing wiring harness unless specifically instructed.

Package Contents

Verify that all components are present before starting the installation:

• 1 x Metra 95-7424 or ND-K753 Double DIN Radio Installation Dash Kit
• 1 x Absolute USA A702-7550 Infiniti Nissan Factory Stereo Radio to Aftermarket Radio Harness Adapter
• 1 x Absolute USA NI6-NI12 Fits Nissan Factory Radio to Aftermarket Antenna Adapter

Image: The Double DIN Dash Kit (left) and the mounting bracket (right) included in the package. The dash kit is a silver-gray plastic bezel designed to integrate an aftermarket radio into the vehicle's dashboard, while the black metal bracket provides structural support for the new radio.

Image: The Absolute USA A702-7550 stereo harness adapter (left) and the NI6-NI12 antenna adapter (right). The stereo harness features multiple color-coded wires for connecting to an aftermarket radio, terminating in white plastic connectors for the vehicle's factory harness. The antenna adapter has a blue and black wire, ending in a white plastic connector and a standard antenna plug.

Setup and Installation

This section outlines the general steps for installing the dash kit and connecting the wiring harnesses. Specific vehicle disassembly instructions are not included and should be referenced from a vehicle-specific service manual or online resources.

Tools Required:

• Panel removal tools
• Screwdrivers (Phillips and flathead)
• Wire strippers/crimpers
• Electrical tape or heat shrink tubing

Installation Steps:

1. Prepare the Vehicle:
   • Disconnect the negative terminal of the vehicle's battery.
   • Carefully remove the factory radio and surrounding dash trim panels. Refer to your vehicle's service manual for specific instructions on dash disassembly.
   • Remove the factory radio from its mounting brackets.
2. Assemble the Dash Kit:
   • Attach the provided mounting brackets from the ABS95-7424 kit to your new aftermarket double DIN radio. Secure them using the screws supplied with your aftermarket radio.
   • Slide the aftermarket radio with attached brackets into the new dash kit bezel. Ensure a snug fit.
   

   Image: The Double DIN Dash Kit and mounting bracket. The aftermarket radio will be secured to the black mounting bracket, which then fits into the silver-gray dash bezel.

3. Wire the Stereo Harness Adapter (A702-7550):
   • Match the color-coded wires of the Absolute USA A702-7550 harness adapter to the corresponding wires on your aftermarket radio's wiring harness.
   • Connect these wires using crimp connectors, solder, or other secure wiring methods. Ensure each connection is insulated with electrical tape or heat shrink tubing.
   • Common wire connections include power (constant 12V, accessory 12V), ground, speaker wires (front left/right, rear left/right), and illumination. Refer to your aftermarket radio's manual for its specific wiring diagram.
   

   Image: Close-up of the Absolute USA A702-7550 stereo harness adapter. This image shows the color-coded wires that connect to the aftermarket radio and the white plastic connectors that plug into the vehicle's factory wiring.

4. Connect the Antenna Adapter (NI6-NI12):
   • Plug the male end of the Absolute USA NI6-NI12 antenna adapter into the antenna input on your aftermarket radio.
   • Connect the female end of the adapter to the vehicle's factory antenna cable.
   

   Image: Close-up of the Absolute USA NI6-NI12 antenna adapter. This adapter facilitates the connection between the vehicle's factory antenna cable and the aftermarket radio's antenna input.

5. Make Final Connections:
   • Connect the wired A702-7550 stereo harness adapter to the vehicle's factory wiring harness. These are typically plug-and-play connections.
   • Ensure all other necessary connections for your aftermarket radio (e.g., parking brake wire, reverse wire, steering wheel control interface if applicable) are made according to your radio's manual.
6. Test the System:
   • Reconnect the vehicle's negative battery terminal.
   • Turn on the vehicle and test the aftermarket radio's functionality: power, audio output, radio reception, and any other features.
7. Reassemble the Dash:
   • Once all functions are verified, carefully mount the aftermarket radio with the dash kit into the vehicle's dashboard opening.
   • Reinstall all removed dash trim panels, ensuring they snap securely into place.

Operating Your Aftermarket Radio

This kit provides the necessary components to install an aftermarket radio. The operation of your new radio will depend on the specific model and brand you have chosen. Please refer to the instruction manual provided with your aftermarket radio for detailed operating instructions.

The Absolute USA harness and antenna adapter are designed for a simple plug-and-play installation, ensuring proper power, ground, speaker, and antenna connections to allow your aftermarket radio to function correctly within your Nissan Titan.

Maintenance

The dash kit and wiring components require minimal maintenance. Keep the dash kit clean by wiping it with a soft, damp cloth. Avoid using harsh chemicals or abrasive cleaners, as these can damage the finish. Ensure all wiring connections remain secure over time. Periodically check for any loose connections, especially if you experience intermittent issues with your radio.

Troubleshooting

If you encounter issues after installation, consider the following:

• No Power to Radio:
  • Check the vehicle's battery connection.
  • Verify all power and ground wires on the A702-7550 harness are correctly connected to the aftermarket radio and the vehicle's factory harness.
  • Check the fuses for both the vehicle and the aftermarket radio.
• No Sound:
  • Ensure all speaker wires from the A702-7550 harness are correctly connected to the aftermarket radio and the vehicle's factory harness.
  • Check the radio's volume and audio settings.
• Poor Radio Reception:
  • Verify the NI6-NI12 antenna adapter is securely connected to both the aftermarket radio and the vehicle's factory antenna cable.
  • Ensure the antenna cable itself is not damaged.
• Dash Kit Does Not Fit:
  • Double-check that your vehicle is a 2008-2012 Nissan Titan, as this kit is specifically designed for these models.
  • Ensure all factory mounting points and clips are clear of obstructions.

Specifications

Warranty Information

Absolute USA products are typically covered by a limited manufacturer's warranty against defects in materials and workmanship. For specific warranty terms and conditions, please refer to the documentation included with your purchase or visit the official Absolute USA website. Keep your proof of purchase for warranty claims.

Customer Support

If you require further assistance with the installation or have questions regarding the Absolute USA ABS95-7424 kit, please contact Absolute USA customer support through their official website or the retailer from whom you purchased the product. Provide your product model number (ABS95-7424) and a detailed description of your issue for efficient support.