Introduction
This manual provides essential information for the installation and maintenance of your SuperDi Clear Blower Fan Belt. This replacement belt is designed for various Simpson, Westinghouse, Kelvinator, Homemaker, and Mistral dryer models. Proper installation is crucial for optimal dryer performance and longevity of the belt.
Product Overview
The SuperDi Clear Blower Fan Belt is a durable replacement part for dryer blower fan systems. It is equivalent to original part numbers 0198001122 and 0198001122K, and also known as B017A and BD005. The belt has a diameter of 260mm and is designed to stretch to fit over the fan motor and pulley, providing the necessary tension for efficient operation.
Figure 1: SuperDi Clear Blower Fan Belt.
Compatibility
This blower fan belt is compatible with a range of dryer models, including but not limited to:
- Simpson: Minimax, Maxidry, Sirocco, and Early Eziset Models.
- Westinghouse: Various models.
- Kelvinator: Various models.
- Homemaker and Mistral: Some series dryers.
Common model numbers this belt suits include: 39-080, 39-081, 39-091, 39-101, 39-111, 39-181-000, 39-191, 39-431, 39B506SE, 39B510SA*12, 39D361P*13, 39D362P*13, 39D452P*13, 39D456S*12, 39D456S*13, 39D457S*12, 39D457S*13, 9D505SR*12, 39D505SR*13, 39D512SA*12, 39D512SA*13, 39P350J*01, 39P350J*02, 39P350K*01, 39P350K*02, 39P350K*03, 39P361E*02, 39P361E*03, 39P362E*02, 39P362E*03, 39S455K*03, 39S456E*02, 39S456E*03, 39S457E*02, 39S457E*03, 39S500J*01, 39S500J*02, 39S500K*01, 39S500K*02, 39S500K*03, 39S505E*02, 39S505E*03, 39S512E*01, 39S512E*02, 39S512E*03, 39S550J*01, 39S550J*02, 39S550K*01, 39S550K*02, 39S550K*03, 39S555J*01, 39S555J*02, 39S555K*01, 39S555K*02, 39S555K*03, 40-201, 40-211, 40-221, 40-241-000, 40-331-00, 40-341-000, 40-391-000, 40-431, 40-441, 40-471, 40-551-000, 40-741, 40-771, 40-841, 40-871, FS50A-01, FS50EA*01, T35AP, T45AS, T45BS-01.
If you are unsure about compatibility with your specific dryer model, it is recommended to verify with the manufacturer or seller.
Installation Instructions
Replacing a dryer blower fan belt requires careful attention. Always ensure the dryer is unplugged from the power source before beginning any installation or maintenance.
- Prepare the Dryer: Disconnect the dryer from the main power supply. Access the blower fan and pulley system according to your dryer's specific service manual.
- Remove Old Belt (if applicable): Carefully remove the old or broken blower fan belt from the motor and pulley.
- Prepare the New Belt: The new belt has a diameter of 260mm. It is designed to stretch. For easier installation, especially in colder conditions, you may place the belt in hot water for a few minutes to increase its flexibility.
- Install the Belt: Position the new belt over the fan motor and the pulley. This step requires significant strength, as the belt needs to be stretched by approximately 2-6cm to achieve proper tension and prevent noise during operation. The new belt may appear smaller than the old one due to wear and tear on the original belt.
- Verify Tension: Ensure the belt is securely seated on both the motor and pulley and has adequate tension. It should feel tight.
- Reassemble Dryer: Reassemble the dryer components that were removed for access.
- Test Operation: Plug the dryer back into the power supply and test its operation to ensure the blower fan is working correctly and quietly.
Important Note: The belt requires considerable stretching (2-6cm) to fit correctly and provide proper tension. This is normal and necessary for its function.
Maintenance
The SuperDi Clear Blower Fan Belt is designed for durability. Regular maintenance of your dryer, such as cleaning lint traps and ensuring proper ventilation, will contribute to the overall longevity of all components, including the blower belt. Inspect the belt periodically for signs of wear, cracking, or fraying. Replace if any damage is observed.
Troubleshooting
- Belt Appears Too Small: This is common. The new belt is designed to be tight and requires significant stretching (2-6cm) to fit over the pulley and motor. The original belt would have stretched and worn over time, making it appear larger.
- Difficulty Installing: If the belt is very stiff, especially in cold environments, try soaking it in hot water for a few minutes to increase its elasticity before attempting installation. Ensure you apply sufficient force to stretch it into place.
- Noisy Operation After Installation: If the dryer is noisy after installation, it may indicate insufficient tension. Ensure the belt is stretched adequately and properly seated on both the motor and pulley. Re-installation with more tension may be required.
- Blower Fan Not Operating: Double-check that the belt is correctly installed and not slipping. Ensure the dryer is receiving power and other components are functioning.
Specifications
| Attribute | Detail |
|---|---|
| Brand | SuperDi |
| Model Numbers | 0198001122, 0198001122K, B017, BD005 |
| Part Number | B017. 0198001122 0198001122K |
| Equivalent to | 0198001022, 0198001022K |
| Belt Diameter | 260mm (unstretched) |
| Color | Clear |
| Condition | New |
Warranty and Support
For information regarding warranty coverage or technical support for your SuperDi Clear Blower Fan Belt, please refer to the purchase documentation or contact the seller directly. Ensure you have your purchase details and product model number (B017, 0198001122, 0198001122K) available when contacting support.