AQUA CONTROL C4110

Download PDF
Contents

Aqua Control C4110 Digital Irrigation Programmer User Manual

Model: C4110

Introduction

The Aqua Control C4110 Digital Irrigation Programmer is designed to simplify your garden watering tasks. Featuring a panoramic Full Vision 2 screen, it allows you to view all programming information at a glance. This device offers easy setup and includes advanced functions such as rain delay, manual watering, and a screen lock to prevent unintended changes. It is certified IPX5 for water resistance, RoHS, and CE compliant.

Aqua Control C4110 Digital Irrigation Programmer showing its panoramic screen and key features like IPX5 protection, screen lock, dual thread compatibility, rain delay, and manual watering.

Figure 1: Aqua Control C4110 Digital Irrigation Programmer with highlighted features.

Setup

1. Battery Installation

The C4110 programmer requires two 1.5V AA alkaline batteries for operation. To install the batteries:

  1. Locate the battery compartment on the back of the device.
  2. Slide the battery cover downwards to open it.
  3. Insert two AA batteries, ensuring correct polarity (+/-).
  4. Close the battery cover securely.
Rear view of the Aqua Control C4110 Digital Irrigation Programmer with the battery compartment open, indicating space for two AA batteries.

Figure 2: Battery compartment on the back of the programmer.

2. Faucet Connection

The programmer is equipped with a dual thread system (1/2" and 3/4") for compatibility with most garden faucets. To connect the programmer:

  1. Ensure the rubber washer is properly seated inside the connector.
  2. Screw the programmer onto your garden faucet. Hand-tighten only to prevent damage.
  3. Connect your garden hose to the outlet of the programmer.
Aqua Control C4110 Digital Irrigation Programmer with 1/2 inch and 3/4 inch thread adapters for faucet connection.

Figure 3: Thread adapters for faucet connection.

3. Initial Time Setting

Upon battery installation, the device will prompt you to set the current time. Use the '+' and '-' buttons to adjust the hour and minute, then press 'OK' to confirm.

Operating Instructions

Basic Programming (4 Steps)

The C4110 programmer guides you through four simple steps to set up your watering schedule:

  1. Set Current Time: Adjust the current time using the '+' and '-' buttons. Confirm with 'OK'.
  2. Set Start Time: Define when watering should begin. Use '+' and '-' to set the desired start time. Confirm with 'OK'.
  3. Set Duration: Specify how long the watering cycle will last. Durations can range from 1 minute to 300 minutes (5 hours) or 1 second to 59 seconds. Confirm with 'OK'.
  4. Set Frequency: Determine how often the watering cycle repeats. Frequencies can range from 1 hour to 23 hours, or 1 day to 15 days. Confirm with 'OK'.
Close-up of the Aqua Control C4110 programmer's screen showing current time, watering duration (60 minutes), frequency (6 hours), and next irrigation time.

Figure 4: Panoramic screen displaying programming information.

Special Functions

  • Manual Watering: To initiate watering outside of the programmed schedule, press the 'MANUAL' button. This allows for immediate watering without altering your set program. Press 'MANUAL' again to stop.
    Icon representing manual watering, a hand pressing a button.
  • Rain Delay: If rain is expected or has occurred, you can temporarily pause the watering schedule. Press the 'RAIN DELAY' button to activate this function. The programmer will resume its schedule after the set delay period.
    Icon representing rain delay, a cloud with raindrops.
  • Screen Lock: To prevent accidental changes to your programming, activate the screen lock function. Refer to the device's on-screen prompts or the included quick guide for specific button combinations to lock/unlock.
    Icon representing screen lock, a padlock inside a shield.
  • Full Vision Display: The panoramic LCD screen provides a clear overview of all programming data, including current time, next watering time, duration, and frequency.
    Icon representing an LCD screen.

Maintenance

Battery Replacement

Replace batteries when the low battery indicator appears on the screen or if the device stops functioning. Always use fresh 1.5V AA alkaline batteries.

Cleaning

Clean the exterior of the programmer with a soft, damp cloth. Do not use abrasive cleaners or immerse the device in water.

Winter Storage

Before the first frost, disconnect the programmer from the faucet. Remove the batteries and store the device in a dry, frost-free location to prevent damage from freezing water.

Troubleshooting

  • No Display: Check if batteries are correctly installed and have sufficient charge. Replace batteries if necessary.
  • No Water Flow: Ensure the faucet is fully open. Check for blockages in the hose or programmer. Verify that the watering program is active and the start time has been reached.
  • Incorrect Watering Times: Review your programming settings (start time, duration, frequency) to ensure they match your desired schedule.
  • Water Leakage: Ensure all connections are hand-tightened and that rubber washers are properly seated and not damaged.

Specifications

FeatureDetail
Model NumberC4110
Dimensions (L x W x H)13 x 7 x 20 cm
Weight392 Grams
MaterialMetal
Power Supply2 x 1.5V AA Alkaline batteries
Water ResistanceIPX5
Faucet Connection1/2" and 3/4" dual thread
Max Watering Duration300 minutes (5 hours)
Max Watering Frequency15 days
CertificationsRoHS, CE
Country of OriginChina

Warranty and Support

The Aqua Control C4110 Digital Irrigation Programmer comes with an Aqua Control warranty. For detailed warranty information, please refer to the documentation included with your purchase or contact Aqua Control customer support.

For additional assistance and visual guides, you can refer to the official product video:

Watch the C4110 Video Guide

This video provides a quick overview of the programming process and key features.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.