lexall 6 Pack LED Motion Sensor Lights - User Manual
Model: LQ-SXQN-CX1A | Brand: lexall
Introduction
This manual provides detailed instructions for the setup, operation, maintenance, and troubleshooting of your lexall 6 Pack LED Motion Sensor Lights. These lights are designed to provide automatic illumination in dark environments, enhancing convenience and safety in various indoor spaces.
Image: Six lexall LED Motion Sensor Lights, illustrating the product packaging.
Safety Information and Warnings
- The light operates only in dark environments. It will not activate if sufficient ambient light is detected.
- Do not install these lights in areas with high temperatures or excessive dampness, as this may affect functionality and adhesive performance.
- To conserve battery life, avoid installing the lights in high-traffic areas where frequent activation is not desired.
- Ensure batteries are installed with correct polarity.
- Before applying the adhesive magnetic strip, clean the surface thoroughly to remove any stains, water, oil, or dust.
- Do not apply the adhesive directly to concave, convex, or rough surfaces, or to human skin.
Package Contents
- 6 x LED Motion Sensor Lights
- 6 x Magnetic Strips with Adhesive Backing
- 1 x User Manual
Specifications
| Feature | Detail |
|---|---|
| Brand | lexall |
| Light Type | LED |
| Special Feature | Energy Efficient, Motion Sensor |
| Wattage | 1 watts |
| Light Color | White |
| Voltage | 1.5 Volts |
| Brightness | 200 Lumen |
| Material | Acrylonitrile Butadiene Styrene (ABS), Aluminum |
| Indoor/Outdoor Usage | Indoor |
| Power Source | Battery Powered |
| Item Model Number | LQ-SXQN-CX1A |
| Product Dimensions | 7.32 x 1.18 x 0.78 inches |
| Batteries Required | 4 x AAA batteries per light (Not Included) |
| Motion Sensor Range | Around 10 feet (3 meters) |
| Motion Sensor Angle | About 120 Degrees |
| LED Quantity | 10 LEDs per light |
Setup
Battery Installation
- Locate the battery compartment cover at one end of the light bar.
- Slide the cover off to open the compartment.
- Insert 4 AAA batteries into the compartment, ensuring correct polarity (+/-). Batteries are not included.
- Slide the battery cover back into place until it clicks securely.
Mounting
- Choose a dry, clean, and flat surface for installation.
- Peel off the protective film from the adhesive side of the magnetic mounting strip.
- Press the magnetic strip firmly onto the desired surface for several seconds to ensure strong adhesion.
- Attach the LED motion sensor light to the magnetic strip. The light can be easily detached for battery replacement.
Image: Step-by-step guide for easy installation using the adhesive magnetic strip.
Operating Instructions
Motion Sensor Functionality
The lexall LED Motion Sensor Lights are equipped with advanced passive infrared (PIR) technology. They are designed for hands-free operation without a manual on/off switch.
- Automatic Activation: The light will automatically turn on when human motion is detected within a 10-foot range and 120-degree angle.
- Automatic Deactivation: The light will automatically turn off after approximately 15-20 seconds of no motion detected.
- Light Sensor: To conserve battery life, the light will only activate in dark or low-light environments. It will not turn on if there is sufficient ambient light.
Image: Automatic sensing lighting, showing activation in darkness upon motion and deactivation after a period of no motion.
Image: Motion detection range of 10 feet and 120 degrees, ideal for illuminating closets.
Maintenance
Battery Replacement
When the light output diminishes or the light stops activating, it's time to replace the batteries. The magnetic mounting system allows for easy battery replacement:
- Gently pull the LED light bar away from the magnetic strip.
- Slide open the battery compartment cover.
- Remove the old AAA batteries and insert new ones, ensuring correct polarity.
- Close the battery compartment cover.
- Reattach the light bar to the magnetic strip.
Troubleshooting
- Light not turning on: Ensure the environment is sufficiently dark. Verify that the 4 AAA batteries are correctly installed and have adequate charge.
- Short battery life: If batteries drain quickly, consider relocating the light from high-traffic areas.
- Adhesive not holding: Ensure the mounting surface is clean, dry, and flat. Avoid damp or high-temperature locations.
- Motion sensor not responding: Check for obstructions to the sensor. Ensure the light is not installed in a high-temperature environment.
Warranty and Support
This lexall product is guaranteed for a period of one year from the date of purchase. For any questions or support, please contact us directly.
Visit the official lexall Store for more products and information.
