HJC DKS468

Download PDF
Contents

HJC DKS468 Pinlock 120 Clear Anti-Fog Lens Instruction Manual

For HJC RPHA 71 Helmet Visors

1. Introduction

This manual provides essential instructions for the proper installation, usage, and maintenance of your HJC DKS468 Pinlock 120 Clear Anti-Fog Lens. The Pinlock 120 lens is designed to prevent fogging on your HJC RPHA 71 helmet visor, ensuring clear vision during various riding conditions. Please read these instructions carefully before installation and use.

2. Product Overview

The HJC DKS468 Pinlock 120 is a high-performance anti-fog insert specifically designed for HJC RPHA 71 helmet visors. It creates an airtight seal between the Pinlock lens and the visor, forming an insulating air pocket that prevents temperature differences from causing fogging.

Note: No relevant product images were provided in the input data for this specific Pinlock lens. The provided image was for a different product (a tablet case) and has been excluded to avoid misinformation.

Note: No relevant product videos were provided in the input data for this specific Pinlock lens.

3. Setup and Installation

Follow these steps to correctly install the Pinlock 120 lens into your HJC RPHA 71 helmet visor:

  1. Prepare the Visor: Remove your helmet visor from the helmet according to your helmet's instruction manual. Ensure the visor is clean and dry.
  2. Remove Protective Film: Carefully peel off the protective film from both sides of the Pinlock lens. Handle the lens by its edges to avoid fingerprints.
  3. Flex the Visor: Gently flex the helmet visor flat. This will allow the Pinlock pins to align correctly with the Pinlock lens.
  4. Position the Pinlock Lens: Align the Pinlock lens with the pins on the inside of your helmet visor. The silicone bead on the Pinlock lens should face the visor.
  5. Engage the Pins: Starting from one side, carefully press the Pinlock lens onto the pins. Ensure the lens is securely seated on both pins.
  6. Check the Seal: Once installed, release the flex on the visor. The Pinlock lens should now be slightly curved and create a tight, airtight seal against the visor. If there are gaps, gently re-flex the visor and adjust the lens until a proper seal is achieved.
  7. Reinstall Visor: Reattach the visor to your helmet.

4. Operating and Usage

Once installed, the Pinlock lens works automatically to prevent fogging. No special operation is required during use. For optimal performance, ensure the lens remains clean.

5. Maintenance

Proper maintenance extends the life and effectiveness of your Pinlock lens:

  • Cleaning: Clean the Pinlock lens only with lukewarm water and a soft, damp cloth. Do not use abrasive cleaners, solvents, or chemical cleaning agents, as these can damage the silicone seal and the anti-fog coating.
  • Drying: Allow the lens to air dry or gently pat it dry with a very soft, lint-free cloth.
  • Storage: When not in use, store your helmet in a clean, dry place away from direct sunlight and extreme temperatures.
  • Replacement: The anti-fog properties of the Pinlock lens may diminish over time with wear and tear or improper cleaning. Replace the lens if you notice reduced anti-fog performance or visible damage.

6. Troubleshooting

If you experience issues with your Pinlock lens, consider the following:

  • Fogging: If fogging occurs, check the seal between the Pinlock lens and the visor. The lens might not be seated correctly on the pins, or the visor might be excessively flexed. Reinstall the lens, ensuring a tight seal.
  • Scratches: Avoid wiping the inside of the Pinlock lens with rough materials or dry cloths, as this can scratch the delicate anti-fog coating. Always use a soft, damp cloth for cleaning.
  • Reduced Performance: Over time, the anti-fog properties may naturally decrease. If cleaning and reinstallation do not resolve the issue, consider replacing the Pinlock lens.

7. Specifications

FeatureDetail
ManufacturerHJC Helmets
BrandHJC
Item Model Number30005409 (DKS468)
Compatible Helmet ModelRPHA 71
Item Weight10.6 ounces
Package Dimensions11.81 x 11.81 x 3.94 inches
MaterialPolycarbonate with silicone seal
ColorClear

8. Warranty and Support

For warranty information or technical support, please refer to the official HJC Helmets website or contact their customer service directly. Keep your proof of purchase for any warranty claims.

Official HJC Website: www.hjchelmets.com

© 2023 HJC Helmets. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.