Introduction
This manual provides essential information for the safe and effective operation, installation, and maintenance of your AgraTronix PW200 Fence Energizer. Please read this manual thoroughly before using the product to ensure proper functionality and to prevent damage or injury.
Figure 1: The AgraTronix PW200 Fence Energizer, showing the main unit, attached power cord, and fence terminals at the bottom.
Safety Information
Always observe the following safety precautions:
- Do not connect the energizer to the mains power supply until all fence and ground connections are made.
- Ensure the energizer is protected from weather elements.
- Keep out of reach of children.
- Do not operate if the unit or power cord is damaged.
- Consult local regulations regarding electric fence installation.
Setup and Installation
The AgraTronix PW200 is designed for easy installation. Follow these steps for optimal performance:
- Mounting: Securely mount the energizer in a dry, protected location, away from direct sunlight and moisture. Use appropriate fasteners for the mounting surface.
- Grounding: Install a proper ground rod (not included) at least 6 feet into the earth, away from other utility grounds. Connect the energizer's ground terminal (typically marked with a ground symbol or "GROUND") to the ground rod using insulated wire. A good ground system is crucial for effective fence operation.
- Fence Connection: Connect the energizer's fence terminal (typically marked with a lightning bolt or "FENCE") to your electric fence line. Ensure all connections are tight and secure. The PW200 is compatible with high tensile wire, poly-wire, poly-tape, poly-rope, and poly-braid fences.
- Power Connection: Once all fence and ground connections are made, plug the energizer into a standard 110V AC outlet. The unit can also be operated using a 12V battery (adapter/cables not included for battery operation).
The energizer features a fence voltage indicator LED, which will illuminate when the unit is properly powered and delivering voltage to the fence.
Operating Instructions
The AgraTronix PW200 operates continuously once plugged in. No user intervention is required for its primary function.
- Power On: Plug the energizer into a 110V AC power source. The LED indicator on the unit will confirm power is being supplied.
- Monitoring: Periodically check the fence voltage indicator LED to ensure the energizer is functioning correctly. A dim or off LED may indicate a problem with the power supply, energizer, or fence line.
- Coverage: The PW200 is designed to energize up to 5 miles of fence wire under optimal conditions and covers up to 5 acres. Performance may vary based on vegetation and fence condition.
Maintenance
Regular maintenance ensures the longevity and effectiveness of your fence energizer.
- Keep Clean: Periodically wipe the energizer casing with a dry cloth to remove dust and debris. Do not use harsh chemicals or immerse in water.
- Inspect Connections: Regularly check all wire connections to the energizer, fence, and ground rod for corrosion or looseness. Clean or tighten as necessary.
- Vegetation Control: Keep vegetation clear from the fence line. Excessive vegetation can "short out" the fence, reducing its effectiveness and putting strain on the energizer.
- Ground System Check: Ensure the ground rod remains firmly in the earth and its connection is secure.
Troubleshooting
If your AgraTronix PW200 is not performing as expected, consult the following table:
| Problem | Possible Cause | Solution |
|---|---|---|
| No LED indicator light / No power to fence | No power from outlet; Faulty energizer; Loose connections. | Check outlet with another appliance. Ensure power cord is fully inserted. Verify all connections are secure. If problem persists, contact support. |
| Weak shock / Reduced fence effectiveness | Poor grounding; Vegetation on fence line; Short circuit on fence; Too long fence line for energizer. | Improve ground system (add more ground rods). Clear all vegetation from fence. Inspect fence for breaks or shorts (e.g., wire touching posts, broken insulators). Ensure fence length is within energizer's capacity (5 miles). |
| Energizer making clicking sound but no shock | Severe short circuit on fence line. | Disconnect fence wire from energizer. If clicking stops and LED lights up, the short is on the fence. Systematically check fence for severe shorts (e.g., broken wire touching ground, metal object across wires). |
Specifications
Key technical specifications for the AgraTronix PW200 Fence Energizer:
- Model: PW200
- Brand: AgraTronix
- Energy Output: 0.20 Joules
- Coverage (Miles): Up to 5 miles (under optimal conditions)
- Coverage (Acres): Up to 5 acres
- Power Input: 110V AC (Plug-in)
- Alternative Power: Can be operated with 12V battery (battery and cables not included)
- Technology: Ultra-Low Impedance
- Indicator: LED Fence Voltage Indicator
- Weight: Approximately 1.67 pounds
Warranty and Support
For warranty information, please refer to the documentation included with your purchase or contact AgraTronix directly. The product is manufactured by AgraTronix.
For technical support or inquiries, please visit the official AgraTronix website or contact their customer service. While a 30-day return policy may apply through your retailer, specific product warranties are typically handled by the manufacturer.
Manufacturer: AgraTronix
Contact Information: Please refer to the manufacturer's official website or product packaging for the most current contact details.
