Introduction
This manual provides essential information for the safe and effective use of your Luceco LED Inspection Head Torch. Please read these instructions carefully before operating the device and retain them for future reference. This head torch is designed for various applications, including professional inspection, DIY tasks, camping, and other outdoor activities, offering versatile lighting modes and hands-free operation.
Figure 1: Front view of the Luceco LED Inspection Head Torch.
Product Overview
The Luceco LED Inspection Head Torch is a versatile and durable lighting solution. Key features include:
- 5 Lighting Modes: Includes 100% output, 50% output, flash mode, red light, and red flash mode.
- PIR Motion Sensor: For hands-free operation, allowing activation and deactivation with a wave of the hand.
- Adjustable Tilt: The torch head can be tilted up to 60 degrees to direct light precisely where needed.
- Rechargeable Battery: Integrated lithium polymer battery, conveniently charged via USB Type-C.
- Durable Construction: Lightweight ABS body with an IK04 rating, designed to withstand tough environments.
- Adjustable Headband: Elastic headband ensures a comfortable and secure fit for various head sizes.
Setup
1. Initial Charging
Before first use, fully charge the head torch. Connect the provided USB Type-C cable to the charging port on the head torch and plug the other end into a compatible USB power source (e.g., computer, USB wall adapter). The charging indicator light will show the charging status. A full charge typically takes approximately 2.5 hours.
Figure 2: USB Type-C charging port for convenient recharging.
2. Adjusting the Headband
Place the head torch on your head. Adjust the elastic headband by sliding the buckles on either side until it fits snugly and comfortably. Ensure the torch unit is centered on your forehead.
Figure 3: The adjustable headband ensures a comfortable and secure fit.
Operating Instructions
1. Powering On/Off and Mode Selection
Locate the power button on the top of the head torch. Press the button to cycle through the following lighting modes:
- First Press: 100% Light Output (150lm)
- Second Press: 50% Light Output
- Third Press: Flash Mode
- Fourth Press: Red Light
- Fifth Press: Red Flash Mode
- Sixth Press: Off
To turn off the torch from any mode, press and hold the power button for approximately 2 seconds.
Figure 4: The head torch offers five versatile lighting modes.
2. PIR Motion Sensing Function
The head torch features a PIR motion sensor for hands-free control. To activate this function, press the dedicated motion sensor button (usually located near the power button). Once activated, you can turn the light on or off by waving your hand in front of the sensor.
3. Tilting the Torch Head
The torch head can be manually tilted up or down to adjust the beam angle. Gently push the torch unit to achieve the desired angle, up to 60 degrees. This allows you to focus light on specific areas without repositioning the entire head torch.
Figure 5: The torch head can be tilted for precise light direction.
Maintenance
1. Cleaning
To clean the head torch, wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents, as these may damage the finish or internal components. Ensure the charging port cover is securely closed before cleaning to prevent water ingress.
2. Battery Care
The integrated lithium polymer battery is designed for long life. To maximize battery longevity:
- Recharge the battery when the light output becomes noticeably dim.
- Avoid fully discharging the battery frequently.
- If storing the head torch for an extended period, charge it to approximately 50% every 3-6 months.
3. Storage
Store the head torch in a cool, dry place away from direct sunlight and extreme temperatures. Keep it away from corrosive materials and out of reach of children.
Troubleshooting
If you encounter issues with your Luceco LED Inspection Head Torch, refer to the following common problems and solutions:
| Problem | Possible Cause | Solution |
|---|---|---|
| Torch does not turn on. | Battery is depleted. | Charge the head torch fully using the provided USB cable. |
| Light is dim or flickers. | Low battery level. | Recharge the battery. |
| Torch does not charge. | Faulty USB cable or power source; charging port obstruction. | Try a different USB cable or power source. Check the charging port for debris and clean if necessary. |
| Motion sensor not responding. | Sensor not activated; obstruction in front of sensor. | Ensure the motion sensor function is activated (press the dedicated button). Clear any obstructions from the sensor area. |
If the problem persists after attempting these solutions, please contact Luceco customer support.
Specifications
| Feature | Detail |
|---|---|
| Model Number | LILH15P65-01 |
| Light Source Type | LED |
| Wattage | 3 Watts |
| Luminous Flux | 150 Lumens |
| Color Temperature | 6500K (Cool White) |
| Beam Distance | Up to 150m |
| Battery Type | Lithium Polymer (included) |
| Charging Time | Approx. 2.5 hours |
| Battery Life (Max) | Up to 20 hours (depending on use) |
| LED Life | 25,000 hours |
| Material | ABS (body), Aluminum (internal components) |
| Color | Black/Green |
| Product Dimensions | 2.7 x 10.6 x 13.1 cm |
| Item Weight | 80 g |
| Ingress Protection (IK Rating) | IK04 |
Warranty & Support
The Luceco LED Inspection Head Torch comes with a 1-year manufacturer's warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use.
For technical assistance, troubleshooting beyond this manual, or warranty claims, please contact the dedicated Luceco technical support team. Please have your product model number (LILH15P65-01) and proof of purchase ready when contacting support.